研究生: |
汪志穎 Chih-Ying Wang |
---|---|
論文名稱: |
鑽削碳纖維強化聚酯之磨耗型態及最佳化研究 Investigation of tool wear and multi-objective optimization in drilling of woven CFRP composite |
指導教授: |
郭俊良
Chun-Liang Kuo |
口試委員: |
蔡宏營
Hung-Yin Tsai 劉孟昆 Meng-Kun Liu |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2017 |
畢業學年度: | 105 |
語文別: | 中文 |
論文頁數: | 71 |
中文關鍵詞: | 碳纖維強化聚酯 、鑽石鍍層刀具 、刀具磨耗型態 、多指標最佳化 |
外文關鍵詞: | woven CFRP laminate, CVD diamond-coated tool, tool wear behaviour, multi-objective optimization |
相關次數: | 點閱:349 下載:2 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
在此研究中,使用化學蒸鍍鑽石鍍層刀具 (直刃型三角鑽與螺旋型雙角鑽) 在切削速度 (50-180 m/min) 與進給速率 (0.05-0.15 mm/rev) 之下,鑽削編織形式碳纖維強化聚酯。探討鑽石鍍層刀具鑽削碳纖維強化聚酯之切削力 (切削推力與扭矩)、刀具磨耗與孔品質 (材料出口脫層及真圓度偏擺),並使用變異數分析 (Analysis of Variance) 來檢視可變因子的顯著性。最後利用決策者可用方程式 (Decision maker’s equation) 建立多重目標之分析模型,藉以達成綜合指標之優化,並搭配顯著因子疊加法得到建議之優化參數區間與預期之品質結果。直刃型三角鑽在第一、第二以及第三刀腹上的磨耗型態分別為刀腹磨損 (Abrasion)、刮痕磨耗 (Scoring) 和鍍層碎裂 (Chipping);螺旋型雙角鑽頭在第一與第二刀刃上的磨耗型態為鍍層碎裂、層間剝離 (Delamination) 以及刀具破損 (Fracture)。由多重目標之分析模型結果可得知,在平均分配各指標之權重下,直刃型三角鑽適合低階切削速 (50 m/min) 配合低階進給 (0.05 mm/rev) 之加工參數。螺旋型雙角鑽則適合低階切削速 (110 m/min) 配合低階進給 (0.05 mm/rev)。由顯著因子疊加法之分析結果可發現,當門檻值設定為實驗結果區間內之25%時,直刃型三角鑽之最佳化參數分布於切削速度 (50-55.46 m/min) 與進給率 (0.052-0.082 mm/rev)。螺旋型雙角鑽在以真圓度為首要考量之最佳化參數範圍為切削速度(110-137.37 m/min) 配合進給率 (0.05-0.069 mm/rev);以第一刃刀具磨耗為首要考量,則是切削速度 (158-180 m/min) 配合進給率 (0.05-0.062 mm/rev)。
This work examines cutting force, tool wear and hole quality with novel geometric designs, such as double-point and multi-facet drills with diamond coatings. Experiments were conducted with the variable of cutting speeds (50-180 m/min) and feed rates (0.05- 0.15 mm/rev) under dry conditions and use ANOVA to examine the signification of variables. To achieve the multi-objective optimization, we used Decision maker’s equation to build up the multi-objective optimization model. And use superposition process map to require the optimal range of parameters. The double-point drill presented various tool wear patterns, including chipping, delamination and fracture on the cutting lips. The tool wear patterns on the multi-facet drill included progressive abrasion wear, scoring and chipping along the cutting lips on the first, second and the third facets respectively. From the multi-objective optimization results under equal weighting of each objective, it suggested that the best combination for multi-facet drill is under the cutting speed of 50 m/min coupling with the feed rate of 0.05 mm/rev. In contrast, double-point drill was suggested to be used under the cutting speed of 110 m/min coupling with the feed rate of 0.05 mm/rev. When the threshold was set to be 25% of the range form experimental results, the superposition process map shows the preferable parameters of multi-facet drill are in the cutting speed of 50-55.46 m/min and the feed rate of 0.052-0.082 mm/rev. Double-point drill’s preferable parameters for out of roundness are distributed in the cutting speed of 110-137.37 m/min and the feed rate of 0.05-0.069 mm/rev. For first flank wear are distributed in the cutting speed of 158-180 m/min and the feed rate of 0.05-0.062 mm/rev.
[1] Abrão AM, Faria PE, Rubio JCC, Reis P, Davim JP. Drilling of fiber reinforced plastics: A review. J. Mater. Proces. Technol. 2007;186(1–3):1-7.
[2] Komanduri R. Machining fibre-reinforced composites. Mech. Eng. 1993;58–66.
[3] Liu D, Tang Y, Cong WL. A review of mechanical drilling for composite laminates. Compos. Struct. 2012;94(4):1265-79.
[4] Tsao CC, Hocheng H. Taguchi analysis of delamination associated with various drill bits in drilling of composite material. Int. J. Mach. Tools and Manuf. 2004;44(10):1085-90.
[5] Poulachon G, Outeiro J, Ramirez C, André V, Abrivard G. Hole Surface Topography and Tool Wear in CFRP Drilling. Procedia CIRP 2016;45:35-8.
[6] Li MJ, Soo SL, Aspinwall DK, Pearson D, Leahy W. Influence of Lay-up Configuration and Feed Rate on Surface Integrity when Drilling Carbon Fibre Reinforced Plastic (CFRP) Composites. Procedia CIRP 2014;13:399-404.
[7] Wang XM, Zhang LC. An experimental investigation into the orthogonal cutting of unidirectional fibre reinforced plastics. Int. J. Mach. Tools and Manuf. 2003;43(10):1015-22.
[8] Bhatnagar N, Ramakrishnan N, Naik NK, Komanduri R. On the machining of fiber reinforced plastic (FRP) composite laminates. Int. J. Mach. Tools and Manuf. 1995;35(5):701-16.
[9] Cadorin N, Zitoune R. Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite. Wear 2015;332–333 742-51.
[10] Raghuveer MS, Yoganand SN, Jagannadham K, Lemaster RL, Bailey J. Improved CVD diamond coatings on WC–Co tool substrates. Wear 2002;253(11–12):1194-206.
[11] Rawat S, Attia H. Characterization of the dry high speed drilling process of woven composites using Machinability Maps approach. CIRP Ann. – Manuf. Technol. 2009;58(1):105-8.
[12] Isbilir O, Ghassemieh E. Delamination and wear in drilling of carbon-fiber reinforced plastic composites using multilayer TiAlN/TiN PVD-coated tungsten carbide tools. J Reinf. Plast. Compos. 2012;31(10):717-27.
[13] Faraz A, Biermann D, Weinert K. Cutting edge rounding: An innovative tool wear criterion in drilling CFRP composite laminates. Int. J. Mach. Tools and Manuf. 2009;49(15):1185-96.
[14] Chen WC. Some experimental investigations in the drilling of carbon fiber-reinforced plastic (CFRP) composite laminates. Int. J. Mach. Tools and Manuf. 1997;37(8):1097-1108.
[15] Murakawa M, Takeuchi S. Mechanical applications of thin and thick diamond films. Surf. and Coat. Technol. 1991;49(1):359-64.
[16] Söderberg S, Gerendas A, Sjöstrand M. Factors influencing the adhesion of diamond coatings on cutting tools. Vacuum 1990;41(4):1317-21.
[17] Enemuoh EU, El-Gizawy AS, Chukwujekwu Okafor A. An approach for development of damage-free drilling of carbon fiber reinforced thermosets. Int. J. Mach. Tools and Manuf. 2001;41(12):1795-814.
[18] Krishnaraj V, Prabukarthi A, Ramanathan A, Elanghovan N, Senthil Kumar M, Zitoune R, Davim JP. Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates. Compos. Part B: Eng. 2012;43(4):1791-9.
[19] Eneyew ED, Ramulu M. Experimental study of surface quality and damage when drilling unidirectional CFRP composites. J Mater. Research and Technol. 2014;3(4):354-62.
[20] Vanderplaats, G.N. Numerical optimization techniques for engineering design. Vanderplaats R&D Inc. ColoradoSprings, CO. 1998.
[21] 李智皓, 振動輔助鑽削於碳纖維/鋁合金疊層材料之切削力、刀具磨耗與孔品質探討. 台灣科技大學研究所碩士論文. 2016.
[22] Tan CL, Azmi AI, Muhammad N. Delamination and Surface Roughness Analyses in Drilling Hybrid Carbon/Glass Compos. Mater. and Manuf. Proces. 2016;31(10):1366-76.
[23] Feito N, Diaz-Álvarez J, López-Puente J, Miguelez MH. Numerical analysis of the influence of tool wear and special cutting geometry when drilling woven CFRPs. Compos. Struct. 2016;138(285-94).
[24] Shetty N, Herbert MA, Shetty R, Shetty DS, Vijay GS. Soft computing techniques during drilling of bi-directional carbon fiber reinforced composite. Applied Soft Comput. 2016;41(466-78).
[25] Roy R, A Primer on the Taguchi Method. 1st ed. Society of Manuf. Eng. 1990.
[26] Chatterjee S, Hadi Ali S. Regression Analysis by Example fifth ed. Wiley. 2012.
[27] Trent E. Wright P. Metal cutting 4th ed. Woburn: Butterworth-Heinemann. 2000.
[28] Smith Graham T. Industrial Metrology: Surfaces and Roundness, Springer-Verlag London. 2002;159.
[29] Tsao CC, Kuo KL, Hsu IC. Evaluation of Novel Approach on Delamination Factor after Drilling Composite Laminates. Key Eng. Mater. 2010;626-630.