研究生: |
葉俊凱 JYUN-KAI YEH |
---|---|
論文名稱: |
分子動力學模擬邊界潤滑狀態下不 同潤滑劑含石墨烯的磨潤行為研究 Tribologicl Behavior study of Different Lubrication Contained Graphene in Boundary Lubrication state by Molecular Dynamics Simulation |
指導教授: |
林原慶
YUAN-QING LIN |
口試委員: |
周育任
YU-REN ZHOU 何羽健 YU-JIANHE |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2022 |
畢業學年度: | 110 |
語文別: | 中文 |
論文頁數: | 227 |
中文關鍵詞: | 分子動力學 、石墨烯 、烷烴分子 、黏著-滑移 、邊界潤滑 |
外文關鍵詞: | Molecular Dynamics, Graphene, Hydrocarbon chain,, Adhesion-slip,, Boundary Lubrication |
相關次數: | 點閱:580 下載:1 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本論文使用分子動力學模擬邊界潤滑狀態下不同潤滑劑含石墨
烯之磨潤行為。並且針對不同分子鏈長的潤滑劑中含不同層數的石墨
烯對磨潤行為的影響進行分析。此外,探討不同層數的石墨烯在不同
的溫度和負載下對磨潤性能的影響。並且,探討石墨烯長度對於磨潤
性能的影響。
結果顯示在未加入石墨烯的條件下,試片進行相對滑動時,
C32H66潤滑劑具有較佳的磨潤行為。烷烴分子隨著分子鏈長越長,黏
度越高,使得潤滑劑之承載能力較好,促使粗糙峰(asperity)的干涉量
降低,具有較佳的磨潤性能。
在相同負載下,含有四層石墨烯的潤滑劑,在摩擦過程中滑動面
之間的間隙相對較大,石墨烯較易進入粗糙峰之間,後續滑動過程的
剪切行為則發生在四石墨烯的層與層之間,使摩擦力明顯減小而有較
好的磨潤行為。
油溫較高時,潤滑劑的黏度和承載能力均下降,導致粗糙峰的干
涉量增加,使磨潤性能下降。較長的石墨烯在潤滑劑中,所承受潤滑
劑流動所產生的拖曳力增加,較易進入粗糙峰之間,防止粗糙峰直接
接觸,避免磨潤行為加劇,能提升磨潤性能。負載較低時含石墨烯潤
滑劑,因上下粗糙峰之間的間隙較大,粗糙峰的干涉量較小,使得摩
擦阻抗下降。
In this paper, molecular dynamics is used to simulate the grinding
behavior of graphene in different lubricants under boundary lubrication.
And the influence of graphene with different layers in different lubricants
on the grinding behavior was analyzed. In addition, the effects of different
layers of graphene on the grinding performance at different temperatures
and loads were explored. Furthermore, the effect of graphene length on the
grinding performance was investigated.
The results show that the C32H66 lubricant has better grinding behavior
when the test piece slides relatively without adding graphene. The longer
the hydrocarbon chain length is, the higher the viscosity, which makes the
bearing capacity of the lubricant better, reduces the interference amount of
the rough peak, and has better grinding performance.
Under the same load, for the lubricant containing four-layer graphene,
the gap between the sliding surfaces is relatively large during the friction
process, and the graphene is easier to enter between the rough peaks, and
the shear behavior of the subsequent sliding process occurs in the fourgraphene Between the layers, the friction force is significantly reduced and
there is a better grinding behavior.
When the oil temperature is higher, the viscosity and load-carrying
capacity of the lubricant decrease, resulting in an increase in the amount of
interference of the asperity peaks and a decrease in the lubricating
performance. Longer graphene in the lubricant increases the drag force
generated by the flow of the lubricant, and it is easier to enter between the
rough peaks, preventing the direct contact between the rough peaks,
avoiding the aggravation of the grinding behavior, and improving the
grinding performance. When the load is low, the graphene lubricant
contains a large gap between the upper and lower rough peaks, and the
interference amount of the rough peaks is small, which reduces the friction
resistance.
Keywords:Molecular Dynamics, Graphene, Hydrocarbon chain,
Adhesion-slip, Boundary Lubrication
1. K. S. Novoselov, A. K. Geim, S. V. Morozov, D. Jiang, Y. Zhang,S.V.
Dubonos, I. V. Grigorieva, and A. A. Firsov, " Eletric field effect in
atomically thin carbon films," Science vol. 306, no. 5696, pp. 666-
669, 2004.
2. A. Koike, M. Yoneya, "Chain Length Effects on Frictional Behavior
of Confined Ultrathin Films of Linear Alkanes under Shear," J. Phys.
Chem. B , vol. 102, pp. 3669-3675, 1998.
3. X. Zheng, H. Zhu n , B.Kosasih, A. K. Tieu, "A molecular dynamics
simulation of boundary lubrication: The effect of n-alkanes chain
length and normal load, " Wear, vol.301, no.1-2, pp. 62-69, 2013
4. Q. Li, C. Lee, R. W. Carpick, and J. Hone, "Substrate effect on
thickness dependent friction on graphene, " Phys. Status Solidi B, vol.
247, no. 11-12, pp. 2909-2914, 2010.
5. A. Smolyanitsky, J. P. Killgore, and V. K. Tewary "Effect of elastic
deformation on frictional properties of few-layer graphene," Physical
Review B, vol. 85, no. 035412, pp. 1-6, 2012.
6. D. H. Cho, L. Wang, J. S. Kim, G. H. Lee, E. S. Kim, S. Lee, S. Y. Lee,
J. Hone, and C. Lee, "Effect of surface morphology on friction of
graphene on various substrates," vol. 5, pp. 3063-3069, 2013.
7. P. Restuccia, and M. C. Righi, "Tribochemistry of graphene on iron
and its possible role in lubrication of steel," Carbon , vol. 106, pp. 118-
124, 2016.
8. J. Dalton, A new system of chemical philosophy. Cambridge
University Press, 2010.
9. J. Irving and J. G. Kirkwood, "The statistical mechanical theory of
transport processes. IV. The equations of hydrodynamics," The
Journal of chemical physics, vol. 18, no. 6, pp. 817-829, 1950.
10. N. Metropolis, A. W. Rosenbluth, M. N. Rosenbluth, A. H. Teller, and
E. Teller, "Equation of state calculations by fast computing machines,"
The Journal of Chemical Physics, vol. 21, no. 6, pp. 1087-1092, 1953.
11. L.Verlet, "Computer" experiments" on classical fluids. I.
Thermodynamical properties of Lennard-Jones molecules," Physical
Review, vol. 159, no. 1, pp. 98-103, 1967.
12. B. Quentrec and C. Brot, "New method for searching for neighbors in
molecular dynamics computations," Journal of Computational Physics,
vol. 13, no. 3, pp. 430-432, 1973.
13. J. E. Jones, "On the determination of molecular fields.—I. From the
variation of the viscosity of a gas with temperature," Proceedings of
the Royal Society of London. Series A, Containing Papers of a
Mathematical and Physical Character, vol. 106, no. 738, pp. 441-462,
1924.
14. J. E. Jones, "On the determination of molecular fields.—II. From the
equation of state of a gas," Proceedings of the Royal Society of London.
Series A, Containing Papers of a Mathematical and Physical Character,
vol. 106, no. 738, pp. 463-477, 1924.
15. M. S. Daw and M. I. Baskes, "Embedded-atom method: Derivation
and application to impurities, surfaces, and other defects in metals,"
Physical Review B, vol. 29, no. 12, p. 6443-6453, 1984.
16. R. A. Johnson, "Alloy models with the embedded-atom method,"
Physical Review B, vol. 39, no. 17, p. 12554-12559, 1989.
17. M. S. Daw, "Model of metallic cohesion: The embedded-atom
method," Physical Review B, vol. 39, no. 11, p. 7441-7452, 1989.
18. Y. Mishin, D. Farkas, M. Mehl, and D. Papaconstantopoulos,
"Interatomic potentials for monoatomic metals from experimental data
and ab initio calculations, "Physical Review B, vol. 59, no. 5, pp. 3393-
3406, 1999.
19. R. A. Johnson, "Analytic nearest-neighbor model for fcc metals,"
Physical Review B, vol. 37, no. 8, p. 3924-3931, 1988.
20. R. A. Johnson, "Phase stability of fcc alloys with the embedded-atom
method," Physical Review B, vol. 41, no. 14, p. 9717-9720, 1990.
21. R. A. Johnson and D. Oh, "Analytic embedded atom method model for
bcc metals," Journal of Materials Research, vol. 4, no. 5, pp. 1195-
1201, 1989.
22. D. W. Brenner, O. A. Shenderova,J. A. Harrison, S. J. Stuart, B. Ni,
and S. B. Sinnott, "A second-generation reactive empirical bond order
(REBO) potential energy expression for hydrocarbons, " Journal of
Physics-Condensed Matter, vol. 14, no. 4, pp. 783-802, 2002.
23. D. W. Brenner, "Empirical potential for hydrocarbons for use in
simulating the chemical vapor-deposition of diamond films. Physical
Review B, vol. 42, no. 15, pp.9458-9471, 1990.
24. J. Byggmästar, M. Nagel, K. Albe, K. O. E. Henriksson, and K.
Nordlund, "Analytical interatomic bond-order potential for
simulations of oxygen defects in iron, " Journal of Physics-Condensed
Matter, vol. 31, no. 215401. pp. 1-13, 2019.
25. M. Tuckerman, B. J. Berne, and G. J. Martyna, "Reversible multiple
time scale molecular dynamics," The Journal of chemical physics, vol.
97, no. 3, pp. 1990-2001, 1992.
26. A. Stukowski, " Structure identification methods for atomistic
simulations of crtstalline materials," Modelling and Simulation in
Materials Science and Engineering, vol. 20, no. 4, 2012.
27. C. W. Gear, " Numerical initial value problems in ordinary differential
equations, " Prentice Hall PTR, 1971.
28. J. Haile, I. Johnston, A. J. Mallinckrodt, and S. McKay, "Molecular
dynamics simulation: elementary methods," Computers in Physics, vol.
7, no. 6, pp. 625-625, 1993.
29. J. M. Haile, "Molecular dynamics simulation, " A Wiley-Interscience
Publication, " pp.260-263, 1992.
30. S. Nosé, "A unified formulation of the constant temperature molecular
dynamics methods," The Journal of chemical physics, vol. 81, no. 1,
pp. 511-519, 1984.
31. W. G. Hoover, "Canonical dynamics: Equilibrium phase-space
distributions," Physical Review A, vol. 31, no. 3, pp. 1695-1696, 1985.
32. S. Plimpton, "Fast parallel algorithms for short-range molecular
dynamics," Journal of computational physics, vol. 117, no. 1, pp. 1-19,
1995.
33. J. Chem, "Development of an improved four-site water model for
bimolecular simulations: TIP4P-Ew," The Journal of Chemical
Physics, vol. 120, no. 20, pp. 9665-9678, 2004.
34. J. E. Lennard-Jones, "Cohesion," Proceedings of the Physical Society,
vol. 43, no. 5, p. 461, 1931.
35. M. I. Mendelev, S. Han, D. J. Srolovitz, G. J. Ackland, D. Y. Sun, and
M. Asta, "Development of new interatomic potentials appropriate for
crystalline and liquid iron," Philosophical Magazine, vol. 83, no. 35 ,
pp. 3997-3994, 2003.
36. P. Schyman, and W. L. Jorgensen, "Exploring adsorption of water and
ions on carbon surfaces using a polarizable force field," The Journal
of Physical Chemistry Letters, vol. 4 , no. 3, pp. 468-474, 2013.
37. P. Li, B. P. Roberts, D. K. Chakravorty, and K. M. M. Jr, "Rational
design of particle mesh ewald compatible lennard jones parameters for
+2 metal cations in explicit solvent, " Journal of Chemical Theroy and
Computation, vol. 9, no. 6, pp. 2740, 2013.
38. M. A. Gonzalez and E. Pellegrini, "MD TURORIAL : Setting up a
simulation (DL_POLY, NAMD, LAMMPS) and analyzing the results
(nMoldyn 4), pp. 19