研究生: |
黃志鴻 Jhih-Hong Huang |
---|---|
論文名稱: |
混料式射出成形螺桿對聚乳酸添加有機蒙脫土複合材料機械性質影響之研究 Effect of Mixing Screw on Mechanical Properties of Injection Molded Polylactic Acid / Organic-Montmorillonite Composites |
指導教授: |
陳炤彰
Chao-Chang Chen |
口試委員: |
楊申語
Sen-Yeu Yang 黃招財 Chiau-Tsai Huang 劉顯光 Hsien-Kuang Liu 吳昌謀 Chang-Mou Wu |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2017 |
畢業學年度: | 105 |
語文別: | 中文 |
論文頁數: | 195 |
中文關鍵詞: | 混料式射出成形螺桿 、生物可降解材料 、聚乳酸高分子 、有機蒙脫土 、機械性質試驗 |
外文關鍵詞: | Mixing screw of injection molding, Bio-degradable materials, Polylactic Acid, Organic Montmorillonite, Mechanical properties |
相關次數: | 點閱:278 下載:1 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本研究探討混料式射出成形螺桿對聚乳酸(Polylactic Acid, PLA)和聚乳酸添加有機蒙脫土(Organic Montmorillonite, OMMT)複合材料的機械性質影響,以直接射出製程對複合材料進行混料成形;利用氨基矽烷偶合劑(Amino-Silane coupling agent)進行有機蒙脫土二次改質,探討聚乳酸添加商用有機蒙脫土(PLA/M)及二次改質蒙脫土之複合材料(PLA/S/M)性質差異性。利用混料式螺桿進行不同蒙脫土比例之複合材料成形,探討雙螺桿押出造粒後由單節距螺桿射出成形試片及直接以混料式螺桿射出成形試片分子結構與機械強度差異性。研究方法首先利用以Flow2000與ANSYS-CFD模組對設計之混料特徵進行流場與混料能力驗證並製造。以實驗設計與迴歸分析方法找出射出成形複材拉伸強度與衝擊強度影響最大之製程參數,並探討兩種製程方法成型試片之機械性質差異性。由實驗結果PLA添加3wt%之商用有機蒙脫土(Cloisite 25A)有較佳機械性質,影響複合材料機械性質為最大因子為料溫;高料溫成形時,混料式螺桿試片抗拉強度與耐衝擊強度相較單節距螺桿試片下降約0.9~12.7%;低料溫進行PLA添加二次改質蒙脫土之成形時,相較於單節距螺桿試片,混料式螺桿試片機械性質上升約7.0~70.6%。本研究之混料式射出形螺桿對PLA添加有機蒙脫土複材研究成果可應用於食品用具與醫用輔具一次性複合材料混料與射出成形。
This study is devoted to design a new type of mixing screw in injection molding to investigate mechanical properties influence of polymer composites by injection molding process. Polylactic Acid (PLA) and PLA composites with Organic Montmorillonite (PLA/M) have been selected to be investigated by regular and mixing screw performed by injection molding. Relation between tensile strength, impact strength, hardness of PLA and PLA/M composites have been tested and discussed. The amino silane coupling agent is selected as interface improving agent of PLA and Organic Montmorillonite (PLA/S/M). Design of injection molding experiment is adopted to find the most significant factor for tensile strength and impact strength of composites sample. Design of such mixing screw has been Flow2000 / ANSYS-CFD simulation for mixing characteristics. Results of shear rate and flow velocity simulation with three feature designs of mixing characteristics. For the best to be fabricated. From experimental results, the better mechanical properties of PLA composites have been obtained by the PLA composites of PLA/M3.0 group. The regression analysis has been used to find the significant factor as melt temperature of injection molding parameter. The processing with low level melt temperature can achieve better mechanical results. With such two types of screw tests, the mechanical properties of PLA composite including tensile strength and impact strength by mixing screw are 0.9~12.7% lower than that of regular screw. Furthermore, process in low level melt temperature, the mechanical properties of tensile strength and impact strength of PLA/S/M composites by mixing screw are higher 7.0~70.6% than those of the single pitch screw. Result of this study can be futher applied on food tableware or medical aids in the one-time molding process in future.
[1] M. Vert, J. Feijen, A. Albertsson, G. Scoot, E. Chiellini, "Biodegradable
polymer and plastics", The Royal Society of Chemistry, Cambridge, London, 1992.
[2] 楊斌,馬振基,"PLA聚乳酸環保塑膠",五南圖書出版,2010。
[3] T. Hideto, Y. Ikada, "Properties and morphology of poly (L‐lactide). II. Hydrolysis in alkaline solution", Journal of Polymer Science Part A: Polymer Chemistry 36.1, pp.59-66, 1998.
[4] YTC America Inc., "Ecology friendly polymeric materials", Available from: http://www.ytca.com/polymers_and_composites.
[5] 漆宗能,"聚合物/層狀矽酸鹽奈米複合材料",五南文化出版社,2004。
[6] R. E. Grim, "Applied Clay Mineralogy", McGraw Hill Book Co., New York, USA, 1962.
[7] M. Önal, "Determination of chemical formula of a smectite", Department of Chemistry, Faculty of Science, Ankara University, TURKEY Series B 52, pp.1-6, 2006.
[8] R.A. Vaia, K.T Rachel, E. P. Giannelis, "Interlayer structure and molecular enviroment of alkylammonium layered silicates", Chemistry of Materials 6.7, pp.1017-1022, 1994.
[9] H. K. Joseoh, "Polymer nanocomposites", McGraw Hill Book Co., New York, USA, 2006.
[10] 楊明,"塑料添加劑應用手冊",江蘇科學技術出版社,2002。
[11] 葉惠珠,"射出成形抗水解聚乳酸複合材料之製備與特性分析",國立臺灣科技大學,機械工程系碩士論文,2017。
[12] 長岡猛,柏眞彦,山口和郎,"射出成形用高分散スクリュの応用研究",成形加工 6.3, pp.163-166,1994。
[13] 張榮語,"射出成型模具設計",高立圖書有限公司,1998。
[14] M. Ruberg, et al, "Experimental Study on the Energy Efficiency of Different Screw Designs for Injection Molding", SPC ANTEC Conference Proceedings, 2008.
[15] I. Akira, et al, "Effect of screw design on fiber breakage and dispersion in injection-molded long glass-fiber-reinforced polypropylene", Journal of Composite Materials 49.1, pp.75-84, 2015.
[16] S. Y. Park, et al, "Transport Behavior of PP in a Plastication Screw of an Injection Molding Machine: Comparison of Standard Screw and Barrier Screw", POLYMER-KOREA 40.3, pp.414-420, 2016.
[17] 馬德君,陳晉南,"塑化過程螺桿計量段三維流場的數值模擬",北京理工大學學報26.6, pp.478-483,2006。
[18] 陳晉南,王鴛鴦,彭炯,"注射螺桿流道熔體非等溫流場的數值研究",北京理工大學學報27.8, pp.723-727,2007。
[19] A. N. Siregar, et al, "Design and analysis of single screw extruder for jatropha seeds using finite element method", Research Journal of Applied Sciences, Engineering and Technology 7.10, pp.2098-2105, 2014.
[20] J. S. Wen, et al, "Numerical Simulation of Mixing Characteristics in a Vane Extruder", Journal of Macromolecular Science, Part B 53.2, pp.358-369, 2014.
[21] G. Karrenberg, J. Wortberg, "3D-CFD-simulation of melting processes in a high-speed-extruder with solid-melt-separation", AIP Conference Proceedings Vol. 1593, pp.623-627, 2014.
[22] M. Jolland, et al, "Effect of mixing conditions on mechanical properties of polylactide / montmorillonite clay nanocomposites", Journal of Applied Polymer Science 118.3, pp.1489-1493, 2010.
[23] E. Kontou, M. Niaounakis, P. Georgiopoulos, "Comparative study of PLA nanocomposites reinforced with clay and silica nanofillers and their mixtures", Journal of Applied Polymer Science 122.3, pp.1519-1529, 2011.
[24] N. Najafi, M. C. Heuzey, P. J. Carreau, "Polylactide (PLA)-clay nanocomposites prepared by melt compounding in the presence of a chain extender", Composites Science and Technology 72.5, pp.608-615, 2012.
[25] M. Yourdkhani, et al, "Thermal, oxygen barrier and mechanical properties of polylactide–organoclay nanocomposites", Composites Science and Technology 82, pp.47-53, 2013.
[26] 李禧俊,"聚乳酸添加有機蒙脫土複合材料之射出成形對機械性質影響",國立臺灣科技大學,機械工程系碩士論文,2014。
[27] G. X. Chen, J. S Yoon, "Thermal stability of poly (L-lactide)/poly (butylene succinate)/clay nanocomposites", Polymer degradation and stability 88.2, pp.206-212, 2005.
[28] S. J. Park, "Effects of a silane treatment on the mechanical interfacial properties of montmorillonite/epoxy nanocomposites", Materials Science and Engineering A 526.1, pp.74-78, 2009.
[29] F. Piscitelli, et al, "Sodium montmorillonite silylation: unexpected effect of the aminosilane chain length", Journal of Colloid and Interface Science 351.1, pp.108-115, 2010.
[30] E. S. Kim, et al, "Effect of the silane modification of clay on the tensile properties of nylon 6/clay nanocomposites", Journal of Applied Polymer Science 117.2, pp.809-816, 2010.
[31] M. A. Ortenzi, et al, "Evaluation of crystallinity and gas barrier properties of films obtained from PLA nanocomposites synthesized via “in situ”, polymerization of l-lactide with silane-modified nanosilica and montmorillonite", European Polymer Journal 66, pp.478-491, 2015.
[32] R.-W. Zhang, D. C. Denise, "Mixer for a plasticizing screw", U. S. Pat., 7296920, 2007.
[33] Kuhman, L. Jon, "Extruder screw with mixing section", U. S. Pat., 7387426, 2008.
[34] T. D. Mazzocca, "Lug type extruder screw", U. S. Pat., 20110222363, 2011.
[35] T. W. Williams, "Mixing section for a plastic extrusion screw", U. S. Pat., 20150298356, 2015.
[36] 黃建銘,"耐熱性聚乳酸樹脂射出成型品之製造方法",中華民國專利,公開號200848244,2008。
[37] 曾水蓮,"耐熱高分子聚乳酸環保塑膠製品射出成型裝置與其製程",中華民國專利,公開號201144039,2012。
[38] 吳宗明,"聚乳酸複合材料及其製造方法",中華民國專利,公開號201238997,2012。
[39] 劉興鑑,"製備奈米聚乳酸系複合材料及聚乳酸系成型品的方法",中華民國專利,公開號201304927,2014。
[40] 黃文盛,"混合PC/PMMA材料應用於LED照明元件射出成形研究",國立臺灣科技大學,機械工程系碩士論文,2012。
[41] 黃俊欽,"塑膠產業專業技術/基礎能力檢定",財團法人塑膠工業技術發展中心,2012。
[42] 陳嶒永,"PMMA-TiO2複合材料之射出成形於功能性二次光學元件之透光性和熱傳導性分析",國立臺灣科技大學,機械工程系碩士論文,2011。
[43] 林昇翰,"可變螺距螺槳之流體動力行為數值模擬",國立臺灣海洋大學輪機工程系碩士論文,2014。
[44] NatureWorks Co., "Ingeo™ Biopolymer 3251D Technical Data Sheet/Injection Molding Process Guide", Available from: http://www.natureworksllc.com.
[45] SONGHAN Plastic Technology Co., "BYK Cloisite® 25A Nanoclay Datasheet", Available from: http://www.lookpolymers.com/index.php.
[46] 富祥達有限公司,"Silane OFS-6020材料特性",Available from: http://www.yahuchi.com/big5/news_detail_6_0。
[47] 田民波,"材料學概論",五南圖書出版有限公司,2015。
[48] 林麗娟,"X光繞射原理及其應用",光材料分析技術應用專題,1994 。
[49] 吳明珠,"儀器分析",新文京圖書,2007。
[50] 博精儀器股份有限公司,"熱分析技術簡介手冊",2002。
[51] 馬振基,"高分子複合材料",華香園出版社,2007。
[52] P. Siwatt, "FTIR Spectra of Organic Functional Group Compositions in PM^ sub 2.5^ Collected at Chiang-Mai City, Thailand during the Haze Episode in March 2012", Journal of Applied Sciences 14.22, pp.2967, 2014.