在研磨加工時所產生的熱，會傳遞至工件以及砂輪顆粒上，造成磨粒的磨耗增加，並且會對工件產生表面及次表面的熱破壞等問題，所以本實驗進行加工區域溫度模組的開發，希望使用者可在實驗前，預測其加工時所產生之溫度，以避免熱對於工件上的破壞。而目前已經有許多研究指出，微量潤滑方式應用於研磨製程中，可以有效地降低加工溫度以及增加磨輪壽命。因此本研究透過微量潤滑方式，將碳酸氫鈉(NaHCO_3)顆粒配合高壓空氣噴出，當作研磨加工時的潤滑劑，其微量潤滑方式只會在工件溫度超過40度時啟動，與乾切削的潤滑方式進行比較，並以其實驗結果進行熱模組的開發，探討碳酸氫鈉以微量潤滑方式噴灑至加工區對於此製程之影響，在實際加工結果顯示，此微量潤滑方式可有效的降低工作溫度以及減少熱影響區，並不會造成表面硬度的改變，在乾切削狀況下，磨粒會被快速地磨耗，造成切削能力下降，使得磨擦力增加，進而使溫度快速的提升，而磨粒大小方面，研究結果顯示越大的磨粒會使溫度上升更為快速。工作溫度模型的參數是由研磨加工參數，例如 : 磨輪速度、微量潤滑壓力等進行建模，並且此模組所模擬出之結果，與實際加工之結果相似，因此驗證此模組是可行的。

Grinding process results in high heat generation at the workpiece-grain interface and most of the heat goes into the workpiece, another fraction is absorbed by the grain and removed by MQL. These high temperatures to the workpiece causes rapid wear of the abrasive grains, surface and sub-surface alteration of the workpiece. A model of the working temperature in both dry and minimum quantity lubrication was developed. In this study, NaHCO_3 particles were spread out with high-pressure air when the threshold of 40°C was exceeded. The results show that the utilization of the surfactant can reduce the working temperature and heat-affected zone efficiently. The hardness of the workpiece is high when the surfactant is applied due to the reduction of the rubbing behavior or efficient dispassion of heat. The simulated results indicate that during dry grinding the temperature rise is rapid as compared to the MQL grinding. The high temperature in dry grinding might be because of immediate wear of the coated abrasive grain, which results in an increase of frictional heat due to large contact area between the abrasive grain and workpiece. The effects of grinding parameters such as mesh size are also analyzed in this study. It is observed that using an abrasive disc of 150 mesh size high temperatures were recorded as compared to 600. The simulation results were verified by the experiments.

[1] Rowe, W., Morgan, M., Batako, A., Jin, T., 2003. “Energy and temperature analysis in grinding”, Transactions on Engineering Sciences, Vol. 44, pp. 3-23.

[2] Howe, T., 1991. “Avoiding thermal damage in grinding”, Joint Industry Conference of the Abrasive Engineering Society, pp. 8-10.

[3] Kuo, W., Lin, J., 2006. “General temperature rise solution for a moving plane source problem in surface grinding”, International Journal Advanced Manufacturing Technology 31, pp. 268-277.

[4] Mahata, S., Mistri, J., Mandal, B., Das, S., 2011. “Coolants and their role in grinding”, Reason-A Technical Journal, Vol. X, pp. 40-44.

[5]. Irani, R., Bauer R., 2011. “A review of cutting fluid application in the grinding process”, International Journal of Machine Tools & Manufacture 45, pp. 1696–1705.

[6] Simões, R., Bianchi, E., Oikawa, S., Aguiar, P., Júnior, R., Canarim, R., 2014. “Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip”, Materials Research, Vol.17, pp.1201-1212.

[7] Silva, L., Bianchi, E., Catai, R., Fusse, R., França, T., Aguiar, P., 2005. “Study on the behavior of the minimum quantity lubricant - MQL technique under different lubricating and cooling conditions when grinding ABNT 4340 steel”, Journal of the Brazilian Society of Mechanical Sciences and Engineering, Vol. XXVII, pp. 192-199.

[8] Hou, Z., Komanduri, R., 2003. “On the mechanics of the grinding process – Part I. Stochastic nature of the grinding process”, International Journal of Machine Tools and Manufacture, Vol.43, pp. 1579-1593.

[9]. Songmene, V., Khettabi, R., Zaghbani, I., Kouam, J., Djebara, A., 2011. “Machining and machinability of aluminum alloys”, CIRP Annals - Manufacturing Technology, Vol 32, pp. 535-540.

[10] Sagar, C., Pal, B., 2014. “Modeling and estimation of grinding forces for mono Layer CBN grinding wheel”, International Journal of Current Engineering and Technology, Special Issue-2, pp. 78-87.
[11] Jaeger, B., 1942. “Moving sources of heat and the temperature at sliding contacts”, Journal Proceedings Society, Vol. 96, pp. 203-224.

[12] Vjayaraghavan, L., 2013. “Theoretical analysis of thermal profile and heat transfer in grinding”, International Journal of Mechanical and Materials Engineering (IJMME), Vol. 8, No. 1, pp. 21-31.

[13]. Malkin, S., Guo, C., 2007. “Thermal analysis of grinding”, CIRP Annals - Manufacturing Technology, Vol 56, Issue 2 pp. 760-782.

[14] Rowe, B., 2009. Principles of Modern Grinding Technology 2nd Edition.

[15] Jen, T., Lavine, A., 1995. “A Variable Heat Flux Model of Heat Transfer in Grinding: Model Development”, Journal of Heat Transfer, Vol. 117, pp. 473-478.

[16] AL-Mokhtar, M., Warkentin, A., Bauer, R., 2012. “Variable heat flux in numerical simulation of grinding temperatures”, The International Journal of Advanced Manufacturing Technology, Vol. 63, pp. 549–554

[17] Ding, Z., Li, B., Fergani, O., Shao, Y., Liang, S., 2016. “Investigation of temperature and energy partition during maraging steel micro-grinding”,9^th International Conference on Digital Enterprise Technology, Intelligent Manufacturing in the Knowledge Economy Era. Procedia CIRP, Vol. 56, pp. 284 – 288.

[18] Upadhyaya, R., Malkin, S., 2004. “Thermal aspects of grinding with electroplated CBN wheels”, Journal of Manufacturing Science and Engineering, Vol. 126, pp. 107-114.

[19] Garcia, E., Méresse, D., Pombo, I., Harmand, S., Antonio, J., 2014. “Sánchez Identification of heat partition in grinding related to process parameters, using the inverse heat flux conduction model”, Journal of Applied Thermal Engineering, Vol. 66, pp. 122-130.

[20] Rowe, B., Morgan, M., Batako, A., Jin, T., 2003. “Energy and temperature analysis in grinding”, Transactions on Engineering Sciences, Vol 44, pp. 3-23.

[21] Santander, G., Placeres, J., Isidro, J., 2011. “Exact Solution for the Time-Dependent Temperature Field in Dry Grinding: Application to Segmental Wheels”, Journal of Mathematical Problems in Engineering, Vol 2011, pp. 1-28.

[22] Vjayaraghavan, L., 2013. “Theoretical analysis of thermal profile and heat transfer in grinding”, International Journal of Mechanical and Materials Engineering (IJMME), Vol. 8, pp. 21-31.

[23] Dorairaju, H., 2015. “Investigation of cutting temperature and cutting force from mist flow pattern in MQL technique”, Faculty of Mechanical and Manufacturing Engineering Universiti Tun Hussein Onn Malaysia. A fulfillment for thesis.

[24] Shao, Y., Li , B., Liang, S., 2015. “Predictive Modeling of Surface Roughness in Grinding of Ceramics”, Journal Machining Science and Technology, Vol.18, pp. 547-564.

[25] Rakholiya, P., Savsani, H., Joshi, A., 2016. “Effect of minimum quantity lubrication (MQL) on grinding”, International Journal of Advances in Production and Mechanical Engineering (IJAPME), Vol. 2, pp. 19-23.

[26] Mao, C., Tang, X., Zou, H., Huang, X., Zhou, Z., 2012. “Investigation of Grinding Characteristic using Nanofluids Minimum Quantity Lubrication”, International Journal of Precision Engineering and Manufacturing, Vol 13, pp. 1745–1752.

[27] Guo, G., Liu, Z., Zheng, X., Chen, M., 2012. “Investigation on surface grinding of Ti-6Al-4V using minimum quantity lubrication”, International Journal of Abrasive Technology, Vol. 5, pp. 84-88.

[28] Sanchez, J., Pombo, I., Alberdi, R., Izquierdo, B., Ortega, N., Plaza, S., Toledano, J., 2010. “Machining evaluation of a hybrid MQL-CO2 grinding technology”, Journal of Cleaner Production, Vol.18, pp. 1840-1849.

[29] Belentania, R., Júniora, H., Canarima, R., 2014. “Utilization of Minimum Quantity Lubrication (MQL) with Water in CBN Grinding of Steel”, Materials Research, Vol. 17, pp. 88-96.

[30] Sadeghi, M., Tawakoli, T., Hadad, M., Vesali, A., Emami, M., Shajari, S., 2014. “An investigation on surface grinding of AISI 4140 hardened steel using minimum quantity lubrication-MQL technique”, International Journal of Material Forming, Vol. 3, pp. 241–251.

[31] Desari, B., Yakhforvazani, M., Khalilpourazary, S., 2015. “The effect of nanoparticle additives on lubrication performance in deep drawing process: Evaluation of forming load, friction coefficient and surface quality”, Vol. 16, pp. 929–936

[32] Kleinstreuer, C., Xu, Z., 2016. “Mathematical Modeling and Computer Simulations of Nanofluid Flow with Applications to Cooling and Lubrication Journal of Fluids”, Journal of fluids, Vol. 1, pp. 1-16.

[33] Abedrabbo, N., Pourboghrat, F., Carsley, J., 2006. “Forming of aluminum alloys at elevated temperatures – Part 2: Numerical modeling and experimental verification”, International Journal of Plasticity, Vol 22, pp. 342-373.

[34] Kuo, C., Chung, C., Wen, J., 2017. “Material removal, surface quality and wear mechanism in coated abrasive grinding of aluminum alloy using minimum quantity lubrication”, Submitted for Journal of Manufacturing Science and Engineering.

[35] Bhushan, B., 2013. Introduction to Tribology 2nd Edition, Tribology series.

[36] Zhang, L., 2012. “Numerical Analysis and Experimental Investigation of Energy Partition and Heat Transfer in Grinding”, Heat Transfer Phenomena and Applications, pp. 79-98.

[37] Mamalis, A., Kundrak, J., Markopoulos, A., 2002. “Numerical simulation for the determination of the temperature fields and the heat affected zones in grinding”, Production Systems and Information Engineering, Vol. 1, pp. 3-16.

[38] Sharma, C., Ghosh, S., Talukdar, P., 2014. “Finite Element Analysis of Workpiece Temperature during Surface Grinding of Inconel 718 Alloy”, International Journal of Research in Engineering and Technology, Vol. 2, pp. 901-906.

[39] Kuo, C., Chung, C., Wen, J., Hsu, Y., 2017. “Multiple criteria optimization in coated abrasive grinding of titanium alloy using minimum quantity lubrication”, Submitted for ASME journal of micro and Nano manufacturing.

[40] Hadad, M., Sadeghi, B., 2012. “Thermal analysis of minimum quantity lubrication-MQL grinding process”, International Journal of Machine Tools and Manufacture, Vol. 63, pp. 1-15.

[41] Feng, Z., Liang, Y., 2017. “Material microstructure affected machining: a review”, Manufacturing Review, Vol. 4, pp. 1-12.

[42] Liao, Y., Luo, S., Yang, T., 2000. “A thermal model of wet grinding process”, Journal of material Procesing Technology, Vol. 101, pp.137-145.

[43] Jin, T., Stephenson, D., 2008. “A study of the Convection Heat Transfer Coefficients of Grinding Fluids”, CIRP Annals - Manufacturing Technology,Vol. 57, pp. 367-370.

[44]Carslaw, H., and Jaeger, J., 1959. Conduction of heat transfer in solids 2nd edition, Oxford Science Publications.

[45]. David, W., Hahn, Necati , M., (2012). Heat Conduction, 3rd Edition, Springer.

[46] Abramowitz, M., Stegun, I., 1964. “Handbook of Mathematical Functions with Formulas, Graphs, and Mathematical Tables”, National Bureau of Standards
Applied Mathematics, Vol. 55, pp. 297-329.

[47] Jin, T., Stephenson, J., 2008. “A study of the Convection Heat Transfer Coefficients of Grinding Fluids”, CIRP Annals - Manufacturing Technology, Vol. 57, pp. 367-370.

[48] Jiang, F., Wang, H., Wang, Y., Xiang, J., 2016. “Simulation of Flow and Heat Transfer of Mist/Air Impinging Jet on Grinding Work-Piece”, Journal of Applied Fluid Mechanics, Vol. 9, pp. 1339-1348.

[49] Vashista1, M., Paul, S., 2014. “Effect of process parameters on convective heat transfer coefficient of fluid and heat partitioning in high efficiency deep grinding with
water based coolant”, International Journal of Machining and Machinability of Materials, Vol. 18, pp. 1-6.