研究生: |
林志鴻 Chih-hung Lin |
---|---|
論文名稱: |
連續沖模之3D電腦輔助沖頭模組設計 3D CAD for Punch Design of Progressive Dies |
指導教授: |
林清安
Ching-An Lin |
口試委員: |
陳炤彰
Chao-Chang Chen 謝文賓 none |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2008 |
畢業學年度: | 96 |
語文別: | 中文 |
論文頁數: | 75 |
中文關鍵詞: | 沖頭設計 、沖頭模組 、連續沖模 |
外文關鍵詞: | punch design, punch module, progressive dies |
相關次數: | 點閱:165 下載:1 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本論文針對連續沖模之沖頭零組件設計問題進行探討,提出以元件模組化與座標系疊合的方法來完成沖頭的設計,以別於以往建構單一沖頭零件,並據以規劃各模板相關零組件的設計方式。本研究亦提出正負零件與建立反向組裝座標系的概念,在取得板料之截面輪廓、道次距離與模板厚度等相關資訊後,即可自動化進行整個沖頭模組的相關零組件幾何設計,並利用零件同動的觀念,正確無誤地與模板結合,完成合理且整體化的沖頭設計。
在雛形系統開發方面,本論文使用Pro/ENGINEER為幾何核心,以一連續沖模的板料為案例,實際建構沖頭模組的3D幾何,藉此印證本論文所闡述的模組架構可有效應用於連續沖模之沖頭設計,並達到快速沖程佈置與即時設計變更的目標。
This thesis investigates the punch design of progressive dies. An approach is proposed which uses component module and coordinate alignment to accomplish the design of punches. It differs from the traditional way of punch design which creates the geometry of each single punch and, accordingly, determines the relevant components of each single mold plate. This thesis also proposes the concept of positive and negative parts and inverse coordinates. Once the data of section contours, pitch distance, plate thickness, etc. are obtained, the geometry of components of the entire punch module can be created automatically. The concept of simultaneous motion of parts is then introduced to accurately assemble the punch module to the mold plates to accomplish a proper and integral punch design.
This thesis uses Pro/ENGINEER as the geometry kernel for prototype system development. The strip of a sample progressive die is also taken as the instance to automate the creation of 3D geometry of the whole punch module. Based on experimental results, it is proven that the methodology proposed in this research work can achieve the goal of rapid strip layout and real-time design change.
1. 郭漢斌,「連續沖模之2D參數化設計」,國立台灣科技大學機械工程系,碩士學位論文,2000。
2. 戴偉翰,「彎形板金展開之3D CAD系統開發」,國立台灣科技大學機械工程系,碩士學位論文,2003。
3. 莊博文,「連續沖模之3D電腦輔助沖程佈置」,國立台灣科技大學機械工程系,碩士學位論文,2003。
4. 劉國彬,「連續沖模之3D電腦輔助板料與沖程佈置」,國立台灣科技大學機械工程系,碩士學位論文,2004。
5. 蕭曉薇,「連續沖模之3D電腦輔助模座設計」,國立台灣科技大學機械工程系,碩士學位論文,2003。
6. 楊雪君,「連續沖模之3D模座設計與2D工程圖輸出」,國立台灣科技大學機械工程系,碩士學位論文,2003。
7. 施啟田,「連續沖模之3D電腦輔助干涉檢測與製程動態模擬」,國立台灣科技大學機械工程系,碩士學位論文,2002。
8. 陳志文,「連續沖模之模座設計與動態模擬之Pro/Toolkit程式開發」,國立台灣科技大學機械工程系,碩士學位論文,2005。
9. 邱贊源,「連續沖模板料設計之Pro/TOOLKIT程式開發」,國立台灣科技大學機械工程系,碩士學位論文,2006。
10. 黃俊鴻,「連續沖模沖頭設計之Pro/Toolkit程式開發」,國立台灣 科技大學機械工程系,碩士學位論文,2006。
11. 李嘉峻,「以Pro/Toolkit進行連續沖模之側向沖頭機構設計」,國立台灣科技大學機械工程系,碩士學位論文,2006。
12. 宋祥瑀,「連續沖模板料沖程佈置之Pro/Toolkit程式設計」,國立台灣科技大學機械工程系,碩士學位論文,2007。
13. 黃重恭,「沖剪模設計原理」,全華科技圖書股份有限公司, 2002。
14. 台灣三住,「MISUMI 沖壓模具用標準零件 2006.11∼2007.10」,台灣三住股份有限公司,2006。
15. 楊志暉,「產品設計幾何資料庫之開發與應用」,國立台灣科技大學機械工程系,碩士學位論文,2007。