本研究是以連續式CO2雷射對AZ61與AZ80鎂合金擠製板材進行銲接，探討熱處理前後對銲接的差異性。並研究銲接參數對機械性質、微觀組織、化學成份、銲接缺陷等的影響，進而改善擠製板材之可銲性。
母材及銲道以掃描式電子顯微鏡(Scanning electron microscope , SEM)觀察及能量分散光譜儀(Energy dispersive X-ray spectroscopy , EDS)分析，發現熱處理後會有更多的鋁與鋅在晶界上偏析。鋁含量高的合金母材在相同入熱量下有較寬的銲道。熔融線附近有較多的鋁偏析，銲道內樹枝狀結構鋁含量也較高。
由實驗結果顯示入熱量越大銲道截面積越大，且熔融線有滲入母材的現象。低入熱量銲接可提升抗拉強度，因為銲道結晶組織緻密及較小的熱影響區，且不易產生不穩定的電漿氣而造成銲道氣孔缺陷。但走速過快會造成較大的過冷區，使熔融線的凝固速率快於部分熔融區，在部份熔融區產生液化裂縫，反而降低抗拉強度。將液化裂縫周圍組織做EDS分析發現鋁偏析的現象。

Investigation of CO2 laser welding has been done to AZ61 and AZ80 magnesium alloy extrusion sheet. Material without heat treatment has been compared with material which heat treated prior to welding. The aim of this research was to study the effect of different heat input of CO2 laser welding on mechanical properties, microstructure, chemical composition and welding defects of the magnesium alloy extrusion sheet in order to improve the weldability.
Base metal and weld metal were observed with the scanning electron microscope. Energy dispersive X-ray spectroscopy analysis reveals that the heat treatment materials have more Al and Zn element segregation in grain boundary. When the alloy with higher aluminum content has wider weld zone in the same heat input relatively. Near the fusion line becomes more Al element segregation and in the weld region the dendritic compounds relatively contain high Al.
Experimental results showed that the width of weld cross section was increased with the increment of heat input, and the fusion line has permeated into base metal. The low heat input would increase tensile strength, because the fusion zone has finer crystal microstructure and the heat affected zone width was reduced. It is difficult to produced unstable plasma which leads to weld porosity. But high welding speed brought the big supercooling area ,fusion line solidify in advance prior to partially melted zone (PMZ), cause liquation cracking in the PMZ which lead to loss of tensile strength. Segregation phenomenon of some Al element in liquation cracking has been taken to analyze by EDS.

[1] 蔡幸甫，「輕金屬產業發展現況及趨勢」，工業材料雜誌，Vol.198，pp.79-80，民國九十二年。

[2] 楊智超，「鎂合金材料特性及新製程發展」，工業材料雜誌，Vol.152，pp.72-73，民國八十八年。

[3] 黃義順、王星豪，「鎂及鎂合金之基本特性與銲接性」，銲接與切割，國立海洋大學，Vol.13，No.3，pp.33-42，民國九十二年。

[4] A. Munitz, C. Cotler and G. Kohn, "Mechanical Properties and Microstructure of Gas Tungsten Arc Welded Magnesium AZ91D Plates," Materials Science and Engineering, A302, pp.68–73(2003).

[5] Liming Liu, Gang Song, Guoli Liang and Jifeng Wang, "Pore Formation During Hybrid Laser-tungsten Inert Gas Arc Welding of Magnesium Alloy AZ31B," Materials Science and Engineering, A390, pp.76–80(2005).

[6] 李長凌，「AZ31B與AZ61A 鎂合金擠製板材CO2雷射銲接性研究」，國立台灣科技大學碩士論文，民國九十六年。

[7]William M.S., Laser Material Processing, London, New York, pp.108-144(1991).

[8] J.D. Majumdar and I. Manna, "Laser processing of materials," Sadhana Vol. 28, Parts 3 & 4, June/August, pp. 495–562(2003).

[9] J. Wilson and J.F. Hawkes., Lasers Principles and Applications, Prentice Hall, New York, pp. 11-13(1987).

[10] T.L. James and E.P. David, "Industrial Lasers and Their Application," Prentice Hall, New York, pp. 153-156(1992).

[11] David Belforte and Morris Levitt, The Industrial Laser Annual Handbook, Vol. 629, p.19(1986).

[12] 王總守，「雷射銲接原理及其應用」，機械月刊，第四卷，第二十一期，pp.220-232，民國八十四年。

[13] C.E. Albright, " Pulsed CO2 Laser Welding," New Orleans, Louisiana, pp.653-665(1981).

[14] Kamel Abderrazak, Wacef Ben Salem, Hatem Mhiri, and Georges Lepalec, "Modelling of CO2 Laser Welding of Magnesium Alloys," Optics and Laser Technology, pp.581–588(2008).

[15] Wang Hai-Xing and Chen.Xi, "Three-dimensional Modeling of the Laser Induced Plasma Plume Characteristics in Laser Welding," Journal of Physics, v36, n6, pp. 628-639(2003).

[16] 陳冠宏，「高功率雷射銲接之特性與應用」，銲接與切割，第六卷，第一期，民國八十四年。

[17] Christopher Dawes, Laser Welding, New York, McGraw-Hill, ch1,(1992).

[18] ASM Handbook, Vol.6,ASM International, Materials Park, OH, pp.528-540 and pp.722-739(1993).

[19] M. T. Perez-Prado and O. A. Ruano, "Texture Evolution During Annealing of Magnesium AZ31 Alloy," Scripta Materialia, pp.149-155(2002).

[20] Taylor Lyman, Metals Handbook 8th Edition-Magnesium Alloys, Vol.8, p.261 and pp.314-319(1976).

[21] Z Zhang, X Zeng and W Ding "The Influence of Heat Treatment on Damping Response of AZ91D Magnesium Alloy," Materials Science and Engineering , A392, pp.150-155(2005).

[22] 鄭力瑋，「AZ80 鎂合金板材之熱間擠製成形性探討」，國立台灣科技大學碩士論文，民國九十六年。

[23] 魏汝超，「鎂合金之熱處理與退火處理之顯微研究」，國立台灣大學碩士論文，民國九十二年。

[24] M. Marya and G.R. Edwards, "The laser welding of magnesium alloy AZ91," Weld World 44 (2), pp.31–37(2000).

[25] M. Ohno, D. Mirkovic and R. Schmid-Fetzer, "Phase Equilibria and Solidification of Mg-rich Mg–Al–Zn Alloys," Materials Science and Engineering, Vol.421, pp.328–337(2006) .

[26] Sindo Kou, Welding Metallurgy, wiley interscience, pp. 156–160 and p.187(2003).

[27] WC Winegard and B Chalmers, "Supercooling and Dendritic Freezing in Alloys," Transactions of American Society of Metals(1954).

[28] X. Cao, W. Wallace, C. Poon and J.P. Immarigeon, "Research and Progress in Laser Welding of Wrought Aluminum Alloys," I. Laser welding processes, Mater Manufact Process, Vol.18, pp.1–22(2003).

[29] X. Cao, W. Wallace, C. Poon and J.P. Immarigeon, "Research and Progress in Laser Welding of Wrought Aluminum Alloys," II. Laser welding processes, Mater Manufact Process, Vol.18, pp.23–49(2003).

[30] M. Mazur, "Porosity in Aluminum Welds," Welding International, pp.929-931(1992).

[31] I.J. Polmear, Light Alloys: Metallurgy of the Light Metals, third ed., Arnold London, p. 207 (1995).

[32] A. Matsunawa, "Problems and Solutions in Deep Penetration Laser Welding," Science and Technology of Welding and Joining, Vol.6, No.6, pp.351-354(2001).

[33] H. Zhao and T. DebRoy, "Pore formation during laser beam welding of diecast magnesium alloy AM60B," Mechanism and Remedy of Welding and Joining, Vol.8, pp.204-210(2001).

[34] S. Jutter, Arc Welding of Magnesium Alloys, Welding of Lightweight Automotive and Railroad Vehicles, Austria, February, pp.26-28 (1997).

[35] 鄭慶民，「熱處理型鋁合金銲接性之研究」，國立交通大學博士論文，民國九十三年。

[36] M. Marya, G. Edwards, S. Marya and D.L. Olson, "Fundamentals in the Fusion Welding of Magnesium and its Alloys," Proceedings of the Seventh JWS International Symposium, Kobe, pp.597–602(2001).

[37] J.R. Crum, K.A. Hech and T.M. Angeliu, "Effect of Different Thermal Treatments on the Corrosion Resistant of Alloy 690 Tubing," EPRI Report NP-6703-M, (1990).

[38] C. Huang and Kou S., "Liquation Cracking in Full-Penetration Al-Mg-Si Welds," Welding Journal, Vol.83, no4 , pp.111-121(2004).

[39] S. Kou, "Solidification and Liquation Cracking Issues in Welding," JOM, pp. 37-42(2003).

[40] M. Marya, G.R. Edwards and S. Lin, "An Investigation on the Effects of Gases in GTA Welding of a Wrought AZ80 Magnesium Alloy," Welding Journal Vol.83, no7, pp.203-211(2004).

[41] R.H. Duley, "An Experimental Investigation of the Constitutional Liquation Hypothesis," Rensselaer Polytechnic Institute, Tory, N.Y(1962).

[42]http://www.matweb.com/search/DataSheet.aspx?MatGUID=d591ab3bc0749039582efb8de674acd