簡易檢索 / 詳目顯示

回結果列表
研究生： 陳福隆
IGNATIUS TOMMY PRATAMA
論文名稱： NUMERICAL STUDY ON SAND BOILING IN EXCAVATIONS AND/OR COFFERDAMS
NUMERICAL STUDY ON SAND BOILING IN EXCAVATIONS AND/OR COFFERDAMS
指導教授： 歐章煜
Chang-Yu Ou
口試委員: 卿建業
Jian-Ye Ching
林宏達
Horn-Da Lin
李安叡
An-Jui Li
學位類別： 碩士
Master
系所名稱： 工程學院 - 營建工程系
Department of Civil and Construction Engineering
論文出版年： 2018
畢業學年度： 106
語文別： 英文
論文頁數： 194
中文關鍵詞： 砂湧 、開挖 、安全係數
外文關鍵詞： SAND BOILING, MODEL FACTOR
相關次數： 點閱：181  下載：8 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • The flow of water through soils in the retaining system may induce some alterations on the magnitude of the working stresses in soils, especially the effective overburden stress. Sand boiling is one of the stability issues related to the change of effective stress due to groundwater flow, but only a few researchers investigate the effect from the effective stress point of view. Accordingly, the primary objective of this study is to investigate the impact of effective stress change inside the excavation zone subject to seepage flow and to evaluate the factors affecting the safety against sand boiling. The study was carried out on 23 experimental failure cases with various excavation geometries and soil densities by utilizing PLAXIS and SEEP/W finite element programs. The results indicate that the failure progression of sand boiling is initiated from the excavation surface, then propagates to the area close to the pile. In addition to the failure propagation, the excavation geometry has a visible effect in establishing the failure mechanism and the governing the computed hydraulic gradient. Concerning the requirement of a reliable safety adequacy, the factor of safety adequacy is proposed in this study by adopting the equivalency theory between reliability and factor of safety. Eventually, two actual failure case histories are introduced to validate the applicability of the proposed factor of safety. The results indicate that the application of the proposed method can describe well the failure condition of an excavation with respect to sand boiling. Note also the application of the proposed factor of safety should obey the applied constraints in this study.

    The flow of water through soils in the retaining system may induce some alterations on the magnitude of the working stresses in soils, especially the effective overburden stress. Sand boiling is one of the stability issues related to the change of effective stress due to groundwater flow, but only a few researchers investigate the effect from the effective stress point of view. Accordingly, the primary objective of this study is to investigate the impact of effective stress change inside the excavation zone subject to seepage flow and to evaluate the factors affecting the safety against sand boiling. The study was carried out on 23 experimental failure cases with various excavation geometries and soil densities by utilizing PLAXIS and SEEP/W finite element programs. The results indicate that the failure progression of sand boiling is initiated from the excavation surface, then propagates to the area close to the pile. In addition to the failure propagation, the excavation geometry has a visible effect in establishing the failure mechanism and the governing the computed hydraulic gradient. Concerning the requirement of a reliable safety adequacy, the factor of safety adequacy is proposed in this study by adopting the equivalency theory between reliability and factor of safety. Eventually, two actual failure case histories are introduced to validate the applicability of the proposed factor of safety. The results indicate that the application of the proposed method can describe well the failure condition of an excavation with respect to sand boiling. Note also the application of the proposed factor of safety should obey the applied constraints in this study.

    ABSTRACT ACKNOWLEDGEMENTS TABLE OF CONTENT LIST OF TABLES LIST OF FIGURES LIST OF SYMBOLS AND ABBREVIATIONS CHAPTER 1 INTRODUCTION 1.1 Research Background 1.2 Research Objectives 1.3 Thesis Structure CHAPTER 2 LITERATURE REVIEW 2.1 Groundwater Flow and Failures due to Seepage Flow 2.2 Overview of the Current Approaches in Quantifying Safety against Failures due to Seepage Flow 2.3 Finite Difference Method in Steady-State Flow Analysis 2.4 Model Uncertainty 2.5 Reliability Analysis 2.5.1 Monte Carlo Simulation (MCS) 2.5.2 Subset Simulation (SubSim) CHAPTER 3 NUMERICAL ANALYSIS ON THE EFFECT OF SEEPAGE TO THE STABILITY OF A SHEETED EXCAVATION 3.1 Analysis of Marsland (1953) Model Test Results 3.1.1 Introduction of Model Tests 3.1.2 Estimation of Ham River Sand (HRS) Soil Parameter 3.2 Assessment of the Predicted Factor of Safety in Failure Cases 3.2.1 Comparison of Sand Boiling Factor of Safety 3.2.2 Assessment of Terzaghi Postulate on the Width of Soil Prism 3.3 Effective Stress Development with Respect to Sand Boiling 3.4 Heave and Factor of Safety Relationship Associated with Sand Boiling 3.5 Summary and Discussions CHAPTER 4 CALIBRATION OF THE CURRENT SAFETY ASSESSMENTS OF SAND BOILING 4.1 Calibration of Model Uncertainties 4.2 Analysis of the Required Factor of Safety by the Reliability Approach 4.2.1 Theorem of Equivalency between Reliability and Factor of Safety 4.2.2 Probability of Failure and Factor of Safety Relationship 4.3 Summary and Conclusion CHAPTER 5 EVALUATION AND VALIDATION PROCEDURES ON THE PROPOSED FACTOR OF SAFETY 5.1 Case Study 1: Excavation in Tokushima Prefecture 5.1.1 Introduction 5.1.2 Soil Parameters and Numerical Model 5.1.3 Evaluation of the Case Study 5.2 Case Study 2: Excavation in Shiga Prefecture 5.2.1 Introduction 5.2.2 Soil Parameters and Numerical Model 5.2.3 Evaluation of the Case Study 5.3 Validation on the Applicability of the Calibrated Factor of Safety Adequacy 5.4 Summary and Discussion CHAPTER 6 CONCLUSIONS AND FUTURE STUDY 6.1 Conclusions 6.1.1 Effective Stress Based-Analysis on the Failure Mechanism of Sand Boiling 6.1.2 Required Factor of Safety and Reliability Approach 6.1.3 Validation of the Proposed Factor of Safety 6.2 Future Study REFERENCES APPENDIX 1 APPENDIX 2 APPENDIX 3

    Altuhafi, F. N., Coop, M. R., & Georgiannou, V. N. (2016). Effect of Particle Shape on the Mechanical Behavior of Natural Sands. Journal of Geotechnical and Geoenvironmental Engineering, 142(12), 04016071.
    Au, S. K., & Beck, J. L. (2001). Estimation of small failure probabilities in high dimensions by subset simulation. Probabilistic engineering mechanics, 16(4), 263-277.
    Bauer, G. E. (1984). Dewatering, hydraulic failure and subsequent analysis of a sheeted excavation.
    Jacob, B. (1979). Hydraulics of groundwater. MacGraw-Hill, New-york.
    Benmebarek, N., Benmebarek, S., & Kastner, R. (2005). Numerical studies of seepage failure of sand within a cofferdam. Computers and Geotechnics, 32(4), 264-273.
    Bolton, M. D. (1986). The strength and dilatancy of sands. Geotechnique, 36(1), 65-78.
    Budhu, M. (2008). SOIL MECHANICS AND FOUNDATIONS. John Wiley & Sons.
    Cai, F., & Ugai, K. (2004). Seepage analysis of two case histories of piping induced by excavations in cohesionless soils. In The first International Conference on Construction,(August 12-14, 2004), www. forum8. co. jp/english/icci/ICCI2004-analysis. pdf.
    Cassagrande, A. (1937). Seepage through dams. Journal of the New England Water Works, 51, pp. 295-336.
    Cedergren, H. R. (1997). Seepage, drainage, and flow nets (Vol. 16). John Wiley & Sons.
    Ching, J. (2009). Equivalence between reliability and factor of safety. Probabilistic engineering mechanics, 24(2), 159-171.
    Darcy, H. (1856). The public fountains of the city of Dijon. Dalmont, Paris, 647.
    Duncan, J. M. (2000). Factors of safety and reliability in geotechnical engineering. Journal of geotechnical and geoenvironmental engineering, 126(4), 307-316.
    Franke, O. L., Reilly, T. E., & Bennett, G. D. (1987). Definition of boundary and initial conditions in the analysis of saturated ground-water flow systems: an introduction. US Government Printing Office.
    Fry, J. (2012). Introduction to the process of internal erosion in hydraulic structures: embankment dams and dikes. Erosion of geomaterials, 1-37.
    Goh, A. T. C., Kulhawy, F. H., & Wong, K. S. (2008). Reliability assessment of basal-heave stability for braced excavations in clay. Journal of geotechnical and geoenvironmental engineering, 134(2), 145-153.
    Harr, M. E. (1962). Groundwater and Seepage. McGraw-H tll, New York.
    Harza, L. F. (1935). Uplift and seepage under dams on sand. Trans. of ASCE, 100, 1352-1406.
    Ishibashi, I., & Hazarika, H. (2010). Soil mechanics fundamentals. CRC Press.
    Japanese Road Association. (1987). Highway Earthwork Series: Manual for Retaining Walls, Culverts and Temporary Works. Tokyo: Japan Road Association: pp.204-242.
    Japanese Road Association. (2002). Specification for the Highway Bridges. Japan Road Association, Tokyo. (in Japanese)
    Juang, C. H., Yang, S. H., & Yuan, H. (2005). Model uncertainty of shear wave velocity-based method for liquefaction potential evaluation. Journal of geotechnical and geoenvironmental engineering, 131(10), 1274-1282.
    Koshla, A.N., N.K. Bose and E. McKenzie Taylor. (1936). Design of Weirs on Permeable Foundations. Central Board of Irrigation, 12, 200 pp.
    Kulhawy, F. H., & Mayne, P. W. (1990). Manual on estimating soil properties for foundation design (No. EPRI-EL-6800). Electric Power Research Inst., Palo Alto, CA (USA); Cornell Univ., Ithaca, NY (USA). Geotechnical Engineering Group.
    Lane, E. W. (1935). Security from under-seepage-masonry dams on earth foundations. In Proceedings of ASCE.
    Mahmud, M. (1996). Spreadsheet Solutions to Laplace'S Equations: Seepage and Flow Net. Jurnal Teknologi, 25, 53-67.
    Marsland, A. R. T. H. U. R. (1953). Model experiments to study the influence of seepage on the stability of a sheeted excavation in sand. Geotechnique, 3(6), 223-241.
    McNamee, J. (1949). Seepage into a sheeted excavation. Geotechnique, 1(4), 229-241.
    Meyerhof, G. G. (1957). Discussion on research on determining the density of sands by spoon penetration testing. In Proceeding of the 4th International Conference on Soil Mechanics and Foundation Engineering. Vol. 1, London, 110.
    Mozó, D., Oróstegui, P., & Villalobos, F. (2014). Hydraulic stability evaluation of a diaphragm wall in granular soils recharged by an unconfined aquifer. Obras y Proyectos, (15).
    Mood, A. M., F. A. Graybill, and D. C. Boes. (1974). Introduction to the Theory of Statistics. 3rd ed., New York: McGraw-Hill.
    Muskat, M. (1937). The flow of fluids through porous media. Journal of Applied Physics, 8(4), 274-282.
    Nanjundan, G., & Raveendra Naika, T. (2012). Asymptotic Comparison of Method of Moments Estimators and Maximum Likelihood Estimators of Parameters in Zero-Inflated Poisson Model. Applied mathematics, 3(6), 610-616.
    NAVFAC DM7-1. (1982). Soil Mechanics, Department of Navy, Naval Facility Engineering Command.
    Ou, C. Y., Liao, J. T., & Lin, H. D. (1998). Performance of diaphragm wall constructed using top-down method. Journal of geotechnical and geoenvironmental engineering, 124(9), 798-808.
    Ou, C. Y. (2006). Deep excavation: Theory and Practice. Taylor and Francis, Netherlands.
    Ohde, J. (1939). Zur Theorie der Druckverteilung im Baugrund. Bauingenieur, 20, 451.
    Ohde, J. (1951). Grundbaumechanik. Hutte, Bd. III, 27 Aufl., 886.
    Phoon, K. K., Liu, S. L., & Chow, Y. K. (2003, June). Estimation of model uncertainties for reliability-based design of cantilever walls in sand. In Proceedings of the International Workshop on Limit State Design in Geotechnical Engineering Practice (LSD 2003). Massachusetts Institute of Technology, Cambridge, Mass.
    Schanz, T., & Vermeer, P. A. (1998). On the stiffness of sands. Géotechnique, 48, 383-387.
    Stearns, F. P., Hasen, A., North, E. P., Ehle, B., Paschke, T., Burr, W. H., ... & Wegmann, E. Discussion of The Bohio Dam by George S. Morison. Transactions of the American Society of Civil Engineers, 48(2), 259-308.
    Tanaka, T. (1994). A case study on piping during excavation for bridge abutments. In Proceedings of International Symposium on Underground Construction in Soft Ground (pp. 159-162).
    Tanaka, T., Hori, H., & Inoue, K. (2002). Boiling occurred within a braced cofferdam due to two dimensionally concentrated seepage flow. In 3rd international symposium, geotechnical aspects of underground construction in soft ground (Vol. 23, No. 25, pp. 33-8).
    Tanaka, T., Song, S., Shiba, Y., Kusumi, S., & Inoue, K. (2012). Seepage failure of sand in three dimensions-experiments and numerical analyses. In 6th International Conference on Scour and Erosion,(August 27-31, 2012), http://scour-and-erosion. baw. de/icse6-cd/data/articles/000144. pdf.
    Tanaka, T., Takashima, W., Pham, T. T. H., Utra, K., & Uemura, N. (2012). A case study on seepage failure of bottom soil within a double-sheet-pile-wall-type ditch. ICSE6 Paris, 27-31.
    Tanaka, T., & Verruijt, A. (1999). Seepage failure of sand behind sheet piles: The mechanism and practical approach to analyze. Soils and foundations, 39(3), 27-35.
    Taylor, D. (1948). Fundamentals of soil mechanics. Chapman And Hall, Limited.; New York.
    Terzaghi, K. V. (1922). Der grundbruch an stauwerken und seine verhutung. Wasserkraft, 17, 445-449.
    Terzaghi, K. V. (1925). Erdbaumechanik. Vienna, F. Deuticke.
    Terzaghi, K. (1943). Theoretical soil mechanics. Wiley, New York.
    Terzaghi, K., Peck, R. B., & Mesri, G. (1996). Soil mechanics in engineering practice. John Wiley & Sons.
    TGS. (2001). Design Specifications for the Foundation of Buildings. Taiwan Geotechnical Society, Taipei, Taiwan.
    Van Zyl, D., & Harr, M. E. (1981, June). Seepage erosion analysis of structures. In Proc., 10th Int. Conf. on Soil Mechanics and Foundation Engineering (Vol. 1, pp. 503-509). Balkema.
    Von Soos, P. (1980). Eigenschaften von Boden und Fels, Ihre Ermitlung im Labor. Grundbau-Taschenbuch, Teil 1, 4 Aufl. Berling: Ernst & Sohn Verlag.
    Weisstein, E. W. (2002). Least squares fitting. Retrieved from http://mathworld.wolfram.com/LeastSquaresFitting.html.
    Wu, S. H., Ou, C. Y., & Ching, J. (2014). Calibration of model uncertainties in base heave stability for wide excavations in clay. Soils and Foundations, 54(6), 1159-1174.
    Wudtke, R. B. (2008, September). Failure Mechanisms of Hydraulic Heave at Excavations. In 19th European young geotechnical engineers’ conference, Gyor, Hungary.
    Yang, K. H., & Wang, J. Y. (2017). Experiment and statistical assessment on piping failures in soils with different gradations. Marine Georesources & Geotechnology, 35(4), 512-527.
    Zaki, H. and S. Leliavsky. (1948). Tail Erosion as a Factor Affecting the Safety Coefficient Against Piping. In Proceedings of the 3rd ICOLD, Vol. II, Questions No.10, R.4, 10 pp.

    QR CODE