研究生: |
王家偉 Jia-Wei Wang |
---|---|
論文名稱: |
應用修正式DANP網路程序分析法於LED自行車燈創新方案優先評選次序及創新設計研究 A study about application of DANP to priority selection order of innovative design plans and innovative design cases of LED bicycle light |
指導教授: |
林榮慶
Zone-Ching Lin |
口試委員: |
許覺良
Chaug-liang Syu 王國雄 Guo-Xiong Wang |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2015 |
畢業學年度: | 103 |
語文別: | 中文 |
論文頁數: | 189 |
中文關鍵詞: | LED自行車車燈 、TRIZ 、DEMATEL 、ANP 、專利 、常態化數值 |
外文關鍵詞: | LED bicycle light, TRIZ, DEMATEL, ANP, patent, normalized numerical value |
相關次數: | 點閱:450 下載:3 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
傳統DEMATEL是透過專家意見以問卷方式決定0~4之影響度之值,分別代表「無影響」、「低影響」、「中影響」、「高影響」、「極高影響」,而本研究首先提出修正式DEMATEL經由常態化數值的概念來評估準則間0~4的相互影響程度。常態化數值是依照多篇專利技術文件經由斷詞斷字系統之重要技術、功能、元件關鍵字出現次數與該高度相關專利群組全文總字數之比值。本研究先以LED閱讀燈為例,初步分類為七項最重要技術準則,透過每個準則所具有的相關技術字以及常態化數值,先計算準則間重複或定義相同的技術字常態化數值,再計算準則間常態化數值佔有之比例,並依所計算出的比例值,來評估決定準則間的相互影響程度0~4之值。接著再依照DEMATEL運算步驟求出總關係影響矩陣、直接/間接關係圖及因果圖,因果圖可協助判斷準則間的相互受影響程度以及哪些準則屬於較為核心技術準則的判定。再將修正式DEMATEL之總關係影響矩陣加入修正式ANP中,形成修正式DANP,本研究先針對LED閱讀燈之三種設計改良方案進行優先評選次序,再將修正式DANP與ANP各自所得之優先設計改良方案作比較後,透過修正式DAMATEL輔助修正式ANP之修正式DANP法所得之優先評選次序計算結果可較符合實際情形。透過LED閱讀燈操作修正式DANP之後,本研究將修正式DANP實際應用於LED自行車燈,經由LED自行車燈產品之相關文獻探討及各項專利分析,將支架結構、夾持部件、散熱鰭片、導熱結構、燈光罩、LED燈源內部配置、電源供應裝置為評選產品設計方案實最重要的評估技術準則,接著透過修正式DEMATEL所分析出的因果圖來解釋七個技術準則的重要度及關連度,發現電源供應裝置為較獨立的準則,與其它準則影響程度低,故本研究之修正式DANP法將電源供應裝置不列入創新方案之優先評選次序內。本研究案例初步擬定LED自行車燈欲改善的三項主要技術,以修正式DANP步驟計算三項創新設計方案的優先評選次序並與修正式ANP比較。最後演算得到三個創新設計方案之優先權值,其優先權值之順序為方案B>方案C>方案A,也就是說方案B之「支撐部結構設計+LED燈源主體結構」為最符合LED自行車燈之最佳產品設計方案。經本文DANP優先評選次序研究以後,本研究再利用修正式TRIZ發明法做改良創新設計,針對創新設計方案B之支撐部結構設計相關的支架連接車燈的快拆結構設計與LED燈源主體結構相關的LED燈源內部配置之燈光反射罩設計做改良創新設計,並得到兩個改良創新設計結果,最後可得到新設計之LED自行車車燈。
Conventional DEMATEL (Decision Making Trial and Evaluation Laboratory) determines degrees of influence at 0~4 scale (0 = no influence; 1 = low influence; 2 = middle influence; 3 = high influence; 4 =extreme influence)by collecting experts’ opinions through questionnaires.But the study proposes a modified DEMATEL that evaluates the mutual influence among 0~4 scales through the concept of normalized numerical value. Normalized numerical value is a ratio of the number of times for appearance of important technical, functional and component keywords, which are obtained from term and word segmentation system, in multiple patent technique documents, to the total number of words in the entire texts of the patent groups with high relativity.First of all, the study takes LED reading lamp for example, and preliminarily classifies its techniques into 7 most important technical standards. Through the related technical words that each standard has and their normalized numerical values, the study firstly calculates the normalized numerical values of repeated technical words among the standards or those having the same definitions. Then the study calculates the ratios of the normalized values among the standards. Based on the ratios calculated, the study assesses the determined mutual influence scales 0~4 among the standards. After that, following the calculation procedures of DEMATEL, the study finds out the general relational influence matrix, direct/indirect relationship diagram, and the causal diagram. The causal diagram can help judge the degree of mutual influence among the standards, and judge which standards belong to more core technical standards. Then the study adds the modified DEMATEL’s calculating the general relational influence matrix to the modified ANP (Analytic Hierarchy Process) to form a modified DANP. Focusing on 3 design improvement plans of LED reading lamp, the study makes a priority order of selection, compares the prioritized design improvement plans obtained respectively from modified DANP and ANP. Through modified DAMATEL assist modified ANP of modified DANP the study makes a priority order of selection calculation results meets the actual circs better. After operation of modified DANP of LED reading lamp, the study practically applies the modified DANP to LED bicycle light. After making the related literature review of LED bicycle light products and analysis of different patents, the study regards support structure, clamping part, heat dissipation fins, heat conduction structure, lamp hood, internal configuration of LED light source, and power supply device as the most important technical evaluation standards for selection of product design plan. After that, the study uses the cause and effect diagram, acquired from analysis by modified DEMATEL, to explain the importance and relativity of 7 technical standards. It is found that power supply device is a more independent standard, and has lower degree of influence than other standards. Therefore, the study’s modified DANP does not list power supply device in the priority order of selection for innovative plans. The study preliminarily determines 3 main techniques to be improved for LED bicycle light, by modified DANP steps to Calculate 3 priority order of selection for innovative plans to compare with modified ANP. Finally, the priority of weights for the 3 innovative design plans are obtained from algorithm. The priority order of weights is: Plan B > Plan C > Plan A . That is Plan B’s “design of support structure + main structure of LED light source.” It best meets the optimal product design plan of LED bicycle light. After making research on the priority order of selection via DANP, the study uses modified TRIZ invention method to improve innovative designs. The study makes improvement in the fast structure dismantling design of support-connected bicycle light, which is related to design of support structure in the innovative design plan B , as well as the light reflected hood in the internal configuration of LED light source, which is related to main structure of LED light source in Plan B. Here two improvement results of innovative design are acquired. Finally, the study acquires the new design of LED bicycle light.
[1].Holonyak, J. N. and Bevacqua, S. F. “Coherent (visible) light emission from Ga (As1-xPx) junctions,” Applied Physics Letters, Vol.1, Issue 4, pp.82-83 (1962).
[2].Steigerwald, D. A., Bhat, J. C., Collins, D., Fletcher, R. M., Holcomb, M.O., Ludowise, M. J., Martin, P. S., and Rudaz, S. L. “Illumination with Solid State Lighting Technology,” IEEE Journal of Selected Topics in Quantum Electronics, Vol.8, Issue 2,pp.310-320 (2002).
[3].McGlen, R.J., Jachuck, R., and S. Lin, “Integrated Thermal Management Techniques for High Power Electronic Devices,” Applied Thermal Engineering, Vol.24, Issue 8-9,pp.1143-1156 (2004).
[4].Jang, D., Yu, S.H., and Lee, K.S. “Multidisciplinary optimization of a pin-fin radial heat sink for LED lighting applications,” International Journal of Heat and Mass Transfer, Vol.55, Issue 4,pp.515-521 (2012).
[5].Culham, J. R. and Muzychka, Y. S., “Optimization of Plate Fin Heat Sinks Using Entropy Generation Minimization, ” IEEE Transactions on Components and Packaging Technologies, Vol.24,pp.159-165(2001).
[6].沈峰民,適用於發光二極體照明設備之調光電路與控制方法,台灣發明專利,I434616(2014)。
[7].黃隆,廣角照射LED燈具構造,台灣發明專利,M389809(2010)。
[8].莊育宗,可攜式閱讀燈具,台灣發明專利,M376685 (2010)。
[9].李克勤,可攜帶型的USB-LED閱讀燈,台灣發明專利,D145568 (2012)。
[10].林嵩哲,蘇文賓,具導光及散熱之自行車燈,台灣發明專利,
M475398(2014)
[11].李文嵩,自行車燈卡固結構,台灣發明專利,M470796(2014)
[12].龔聰明,具車燈功能之自行車袋體快拆扣具,台灣發明專利,M365880(2009)
[13].陳勝宗,可散熱的自行車車燈,台灣發明專利,M337513(2008)
[14].Goldfire Innovator, http://www.invention-machine.com/index.htm
[15].Liu, C. C. and Chen, J. L., “Development of Product Green Innovation Design Method,” Proceedings of EcoDesign : Second International Symposium on Environmentally Conscious Design and Inverse Manufacturing, Tokyo, Japan,pp.168-173. (2001).
[16].Liu, C. C. and Chen, J. L., “A TRIZ Inventive Product Design Method without Contradiction Information,” The TRIZ Journal, Paper No. 6, http://www.triz-journal.com (2001).
[17].Chang, H. T. and Chen J. L., “An Approach Combining Extension Method with TRIZ for Innovative Product Design,” Journal of the Chinese Society of Mechanical Engineers, Vol.25,pp.13-22 (2004).
[18].Low, M. T., Lamvik, K. W., and Myklebust, O., “Manufacturing a green service: engaging the TRIZ model of innovation,” IEEE Transactions on Electronics Packaging Manufacturing, Vol. 24, Issue 1, pp.10–17 (2001).
[19].Chang, H. T. and Chen, J. L., “The Conflict-Problem-Solving CAD Software Integrating TRIZ into Eco-Innovation,” Advances in Engineering Software, Vol.35, Issue 8-9,pp.553-566 (2004).
[20].Wang, H., Chen, G., Lin Z., and Wang, H., “Algorithm of Integrating QFD and TRIZ for the Innovative Design Process,” International Journal of Computer Applications in Technology, Vol.23, Issue 1, pp.41-52 (2005).
[21].Tong, L. H., He, C., and Shen, L., “Automatic Classification of Patent Documents for TRIZ Users,” World Patent Information, Vol.28,pp.6-13 (2006).
[22].Terninko, J., ”The QFD, TRIZ and Taguchi Connection : Customer– Driven Robust Innovation,” The Ninth Symposium on Quality Function Deployment,pp.374-380 (1997).
[23].León-Rovira, N. and Aguayo, H., “A new Model of the Conceptual Design Process using QFD/FA/TRIZ,” The TRIZ Journal. http://www.triz-journal.com/, July (1998).
[24].Apte, P. R. and Mann, D. L., “Taguchi and TRIZ: Comparisons and Opportunities,” The TRIZ Journal, http://www.triz-journal.com/, November, (2001).
[25].Mann, D. L., “Assessing the Accuracy of the Contradiction Matrix For Recent Mechanical Inventions,” The TRIZ Journal. http://www.triz-journal.com/, February (2002).
[26].Fey, V. and Rivin, E., “Innovation on Demand: New Product Development Using TRIZ,” Cambridge University Press, UK,(2005).
[27].Savransky, S. D., “Engineering of Creativity –Introduction to TRIZ Methodology of Inventive Problem Solving,” CRC Press, New York, (2000).
[28].鄭振興,「利用知識工程技術進行支撐結構設計評估與設計改善之研究」,國立台灣科技大學機械工程學系,博士論文,台北(2011)。
[29].黃浩誠,「應用改良之TRIZ理論結合QFD於補償式化學機械拋光終點偵測及補償路徑之改善」,國立台灣科技大學機械工程學系,碩士論文,台北(2007)。
[30].Fontela, E., Gabus, A., “The DEMATEL observer ,” Battelle Geneva Research Center, Switzerland Geneva.(1976).
[31].Tzeng, G. H., Chiang, C. H., Li, C. W., “Evaluating intertwined effects in e-learning programs: A novel hybrid MCDM model based on Factor Analysis and DEMATEL,” Expert Systems with Applications Vol.32, No4, pp.1028-1044.(2007).
[32].Ou Yang, Y. P., Shieh, H. M., Leu, J. D. and Tzeng, G. H., “A Novel Hybrid MCDM Model Combined with DEMATEL and ANP with Applications”, International Journal of Operations Researc, Vol.5, No.3 , pp.1-9. (2008).
[33].李杰穎,「以混合多目標決策方法建立永續供應商評估模型」,中原大學工業與系統工程學系,碩士論文,桃園(2013)。
[34].Sugiyanto and Rochimah, S.,“ Integration of DEMATEL and ANP methods for calculate the weight of characteristics software quality based model ISO 9126,” Information Technology and Electrical Engineering (ICITEE), International Conference.(2013).
[35].Wu,W. W., “Choosing knowledge management strategies by using a combined ANP and DEMATEL approach,” Journal of the Expert Systems with Applications, Vol.35, Issue 3, pp.41-52 (2005).
[36].李惟萱、黃心慧、溫筑宜,「節能減碳新世代──LED 發光二極體」,工程技術類,台北(2011)。
[37].賴威蒼,「結合修正式TRIZ及電腦輔助工程分析改善LED檯燈結構之研究」,國立台灣科技大學機械工程學系,碩士論文,台北(2011)。
[38].黃志銘,「LED水族燈之結構與散熱改良研究」,國立台灣科技大學機械工程學系,碩士論文,台北(2012)。
[39].陳啟銘,「結合修正式分析網路程序法與修正式TRIZ發明方法應用於LED閱讀燈創新設計方案優先次序評估」,國立台灣科技大學機械工程學系,碩士論文,台北(2013)。
[40].Lin, Z. C. and Chen C. C., “Innovation Procedure for Polishing Times Calculations of Compensated CMP Using Multiple Steps of The Modfied TRIZ Method,” Journal of Innovative Computing, Information and Control, Vol.5, pp.2311-2332. (2009).
[41].Altshuller, G., “The 40 Principles,” Technical Innovation Center, Inc. Worcester, MA (1997).
[42].Saaty, T. J, “Decision making in Complex Environments,” The Analytical Hierarchy Process for decision Making with Dependence and Dependence and Feedback , RWS Publications ,USA. (1996).
[43].Saaty, T. L. and Takizawa, M., “Dependence and independence: From linear hierarchies to nonlinear networks,” European Journal of Operational Research, Vol.26,Issue 2 ,pp.229-237 (1986).
[44].Lin, C. J. and Wu, W. W., “ A causal analytical method for group decision-making under fuzzy environment . ” Expert Systems with Applications Vol.34,No.1 ,pp.205-213. (2008).
[45].Han, W. M., Hsu, C. H. and Yeh, C. Y., “Using DEMATEL to Analyze the Quality Characteristics of Mobile Applications.” Proceedings of the 2014 International Conference on Future Information Engineering and Manufacturing Science ,pp.131-134(2014).