研究生: |
黃玠豪 Jie-Hau Huang |
---|---|
論文名稱: |
鋼筋混凝土構件平面應力配筋及美國規範ACI與歐洲規範EN之比較 Reinforced concrete member plane stress design and contrast between American ACI standard and Eurocode |
指導教授: |
潘誠平
Chan-Ping Pan |
口試委員: |
廖國偉
Kuo-Wei Liao 蔡幸致 Hsing-Chih Tsai |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 營建工程系 Department of Civil and Construction Engineering |
論文出版年: | 2013 |
畢業學年度: | 101 |
語文別: | 中文 |
論文頁數: | 108 |
中文關鍵詞: | 平面應力 、SAP2000 、歐洲規範EN |
外文關鍵詞: | Plane Stress, SAP2000, Eurocode EN |
相關次數: | 點閱:216 下載:0 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本研究分為兩個部份,第一部份為平面應力構件的配筋規則之介紹。一般而言鋼筋混凝土深梁、牆、版殼結構仍然以軸力加彎矩或剪力分析,但由於規範對於配筋的制定有些不合理處,容易造成使用者在配置鋼筋時的理論根據和實驗驗證不能完全相符,進而對整體結構分析的錯誤認知,故本研究採用有限元素平面應力分析型式,針對適用於有限元素法之平面應力元素能模擬之構件進行分析。
第二部份為初步研讀歐洲規範EN,並根據歐洲規範EN1992-1-1給定之構件抗剪承載力公式,與美國規範ACI318-02給定之公式進行公式比較,利用曲線圖得知歐洲規範EN1992-1-1與美國規範ACI318-02各自的公式隨參數的改變而其抗剪承載力也隨之改變的走勢。
There are two parts in this research. First is the introduction of plane stress member’s design. In general, reinforced concrete deep beam, wall and slab still analyze by axial force and bending moment or shear strength, but due to the unreasonable part of specification, likely to cause users’ theoretical basis cannot exactly match the experiment, and have an error on the overall perception of structural analysis. So, this study takes analysis of planar structure using finite element method. For those members which can be simulate by finite element method of plane stress method.
Second, preliminary study the Eurocode (EN), and base on the shear capacity for reinforced concrete members equation that given from EN1992-1-1, and contrast with the equation from American ACI standard (ACI318-02). When the parameters in both equations from EN1992-1-1 and ACI318-02 changes, the curve graph of shear capacity for reinforced concrete member’s trend will also change.
【1】「Building Code Requirements for Structural Concrete with Design Application」, ACI 318-02.。
【2】劉志堅,「樓板水平剪力分析暨鋼筋混凝土平面應力元件配筋原則」,國立台灣科技大學營建工程系研究所碩士論文,民國八十四年。
【3】許世群,「鋼筋混凝土平面應力構件配筋原則之研擬」, 國立台灣科技大學營建工程系研究所碩士論文,民國九十二年。
【4】王世華,「鋼筋混凝土構件平面應力配筋及轉化直桿元素穩定所需剪力元素探討」國立台灣科技大學營建工程系研究所碩士論文,民國一百零二年。
【5】林聰悟,「由三維應力計算鋼筋混凝土之鋼筋量」。
【6】H.B. Kupfer, H.K. Hilsdorf and H. Rusch,(1969),「Behavior of concrete under biaxial stresses.」。
【7】D. Darwin and D.A. Pecknold,(1977),「Nonlinear Biaxial Stress-Strain Law for Concrete.」,J. of Engineering Mechanics Division.。
【8】「混凝土工程設計規範與解說」,中國土木水利工程學會,土木401-93,民國九十三年。
【9】E. Hognestad,「A Study of Combined Bending and Axial Load in Reinforced Concrete Members.」Bullet in NO. 399 , Engineering,1951.。
【10】BS EN 1992-1-1:2004,Eurocode 2: Design of Concrete structures.