研究生: |
吳聰維 WU-TSUNG WEI |
---|---|
論文名稱: |
於CNC加工中心機對Al-6061T6鋁合金進行表面精加工研究 Research on the Surface Finish of Al-6061T6 on a CNC Machining Center |
指導教授: |
修芳仲
Fang-Jung Shiou |
口試委員: |
向四海
Su - Hai Hsiang 蔡曜陽 Yao-Yang Tsai |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2017 |
畢業學年度: | 105 |
語文別: | 中文 |
論文頁數: | 123 |
中文關鍵詞: | 球擠光 、球拋光 、田口法 、ANOVA變異數分析 、五軸加工 |
外文關鍵詞: | Ball burnishing, Ball polishing, Taguchi’s method for experiments, ANOVA analysis, Five-axis CNC machining |
相關次數: | 點閱:465 下載:1 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本研究目的為於CNC切削中心機上對Al-6061T6發展自動化表面精加工製程。本研究以田口實驗計畫法對Al-6061T6找出球擠光與球拋光最適參數,並以三軸、五軸工法將最適化加工參數應用於3D自由曲面,以探討不同工法對3D自由曲面之表面粗糙度改善情形。
本研究以L9(34)直交表進行球擠光與球拋光之田口實驗,找出最適化加工參數,並以ANOVA變異數分析探討各加工參數對於表面粗糙度的影響。由實驗結果得到最適球擠光加工參數為:擠光力90N、進給300mm/min、間距200μm,可使2D平面試件表面粗糙度改善Ra 0.22μm;最適球拋光加工參數為:主軸轉速12,000rpm、進給40mm/min、間距40μm、壓深90μm(=1N),可使2D平面試件表面粗糙度改善至Ra0.14μm。
最後,本研究將所得最適球擠光與球拋光參數應用於3D自由曲面,並分別以三軸、五軸加工中心機進行加工,比較三軸工法與五軸工法對3D自由曲面表面粗糙度的改善情形。結果顯示以五軸工法進行球擠光與球拋光加工所得到的表面改善情形皆優於三軸。
The objective of this research is to develop a ball burnishing and ball polishing surface finish process on a three-axis and five-axis CNC machining center, respectively, to improve the surface roughness of Al-6061T6. The optimal plane surface ball burnishing and ball polishing parameters have been determined by conducting the Taguchi’s L9 matrix experiments, ANOVA analysis, and the verification experiments, respectively. The determined optimal ball burnishing parameters were as follows: the burnishing force of 90 N, the feed rate of 300 mm/min, the step over of 20 μm. The surface roughness of the flat specimens could be improved from Ra 0.8μm to Ra 0.22μm by using the determined optimal ball burnishing parameters. The optimal ball polishing parameters were as follows: the spindle speed of 12,000 rpm, the feed rate of 40 mm/min, the step over of 40 μm, the depth of penetration of 90 μm (1N). The surface roughness of the flat burnished specimens could be improved from Ra 0.22μm to Ra 0.14μm. Finally, the optimal ball burnishing and ball polishing parameters were applied to a 3D aspherical surface by using three-axis and five-axis CNC machining center, respectively. The difference of surface roughness between the three-axis process and the five-axis process has been investigated. The improvement of the surface roughness was better by using the five-axis process compared with the three-axis process.
1.M. Nemat and A.C. Lyons, “An investigation of the surface topography of ball burnished mild steel and Aluminium,” Manufacture Technology, Vol. 16, pp. 469-476, 2000.
2.M.M. El-Khabeery and M.H. El-Axir *, “Experimental techniques for studying the effects of milling roller-burnishing parameters on surface integrity”, International Journal of Machine Tools & Manufacture Vol. 41 pp. 1705–1719, 2001.
3.W. Bouzid, O. Tsoumarev, and K. Sai, “An investigation of surface roughness of burnished A1S1 1042 steel”, Int J Adv Manuf Technol Vol. 24 ,pp. 120-125, 2004.
4.Liviu Luca, Sorin Neagu-Ventzel and Ioan Marinescu, “Effect of working parameterson surface finish in ball-burnishing of hardened steels”, Precision Engineering, 2005.
5.N.S.M. El-Tayeb *, K.O. Low and P.V. Brevern,“Influence of roller burnishing contact width and burnishing orientation on surface quality and tribological behaviour of Aluminium 6061”, Journal of Materials Processing Technology Vol. 186, pp. 272–278, 2007.
6.莊俊雄,“創新型內建荷重計擠光工具應用於工具鋼自動化表面精加工之研究”,國立台灣科技大學機械工程碩士論文,2007年。
7.林孫鵬, “7075-T651鋁合金之球擠光製程研究” ,國立台灣科技大學機械工程學系碩士論文,2008年。
8.N.S.M. El-Tayeb *, K.O. Low and P.V. Brevern, “On the surface and tribological characteristics of burnished cylindrical Al-6061”, Tribology International Vol. 42, pp. 320–326. 2009.
9.Zhengqiang Tang, Wei Xia, Fenglei Li, Zhaoyao Zhou and Jing Zhao, "Application of response surface methodology in the optimization of burnishing parameters for surface integrity", School of Mechanical and Automative Engineering., SCUT, 2010.
10.Aysun Sagbas, “Analysis and optimization of surface roughness in the ball burnishing process using response surface methodology and desirability function”, Advances in Engineering Software, Vol. 42, No. 11, pp. 992-998, 2011.
11.黃仕儒,“新型內建荷重計球擠光工具整合於CNC車床對塑膠模具剛表面精加工之研究”,國立台灣科技大學機械工程系碩士論文,2016年。
12.K. Sasaki, T. Miyoshi, K. Saitoh and S. Okada, “Development and construction of polishing apparatus, knowledge acquisition and automation of polishing operation for injection mold” , Vol. 12, pp. 93-99, 1992.
13.李伯益,“撓性夾持機構應用在研磨與拋光之研究”,淡江大學機械工程學系碩士班碩士論文,1998年。
14.高瑞隆,“機械拋光工藝:細拋時拋光液對於Al-6061合金表面光澤度的影響”,虎尾科技大學材料科學與綠色能源工程研究所,2012。
15.徐智誠,“以球擠光與拋光製程做塑膠模具用鏡面不銹鋼之表面精加工研究”,國立台灣科技大學機械工程碩士論文,2005年。
16.邱泓翔,“振動式球拋光製程作鏡面不銹鋼之自動化表面精加工研究”,國立台灣科技大學機械工程學系碩士論文,2006年。
17.陳茂全,“於CNC工具機進行自動球拋光之定力控制研究”,國立台灣科技大學機械工程學系碩士論文,2008年。
18.張端鴻,“新型內建荷重計球拋光工具之研製”,國立台灣科技大學機械工程系碩士論文,2014年。
19.徐銘良,“於CNC工具機進行自動球拋光之定力控制研究”,國立台灣科技大學機械工程系碩士論文,2015年。
20.Qiaoling Yuan, Huan Qi * and Donghui Wen,“Numerical and experimental study on the spiral-rotating abrasive flow in polishing of the internal surface of 6061 aluminium alloy cylinder”,Powder Technology, Vol. 302, pp. 153–159, 2016.
21.丁肇力,“超音波球拋光製程作鏡面不鏽鋼之自動化表面精加工研究”,國立台灣科技大學機械工程系碩士論文,2016年。
22.樓成章,“鋁合金高速銑削特性之研究”,國立成功大學機械工程研究所碩士論文,1991年。
23.廖俊雄,“鋁合金高速切削對表面精度影響之研究”,國立中正大學機械工程研究所碩士論文,1994年。
24.彭德禮,“表面粗糙度及疲勞壽命之相關性研究”,國立台灣科技大學機械工程技術系碩士論文,1994年。
25.范光照,黃偉明,“精密曲面加工與機上量測系統的研製”,中國機械工程學會第14屆全國學術研討會論文集,1997年。
26.“粗糙度量測參數之新趨勢”,機械月刊第27卷第11期,
2001年。
27.陳耀茂譯,“田口實驗計畫法”,滄海書局,1997年。
28.劉克琪,“實驗設計與田口式品質工程”,華泰書局,1994年。
29.林秀雄,“田口方法與品質工程”,新知企業有限公司,1997年。
30.鄭燕琴,“田口品質工程技術-理論與實務”,中華民國品質管制學會,1993年。
31.李輝煌,“田口方法-品質設計的原理與實務”,高立圖書有限公司,2000年。
32.黎正中譯,“穩健設計之品質工程”,台北圖書有限公司,
1983年。
33.張郭益、許全守編著,“精密量測 ”,全華書局,2003年初版。
34.黃健勝,“使用撓性機構以降低拋光力量變化”,淡江大學機械工程學系碩士論文,1999。
35.周孟賢,“化學機械研磨時控製程參數最佳化技術”,國立中興大學機械工程學系,2000。
36.郭寬淵,“電解拋光鋁合金微流道模具之研究”,國立中央大學機械工程研究所,2008。
37.M. Geiger, M. Kleiner, R. Eckstein, N. Tiesler and Engel U., “Microforming,” Vol. 50, No. 2, pp. 445-462, 2001.
38.X. Wu, Y. Kita and K. Ikoku, “New polishing technology of free form surface by GC, materials processing technology,” Vol. 187-188, pp. 81-84, 2007.
39.M. Nemat and A.C. Lyons, “An investigation of the surface topography of ball burnished mild steel and Aluminium,” Manufacture Technology, Vol. 16, pp. 469-476, 2000.
40.賴廷鏤,“鋁合金 6061-T6 銑削加工表面粗糙度最佳化切削參數研究”,元智大學機械工程研究所,碩士論文,1997。
41.台灣盛百股份有限公司,2003年。
42.台灣聯合磨料股份有限公司,2011年。
43.致洋實業股份有限公司,1997年。
44.“Modle 53 performance specifications”,Honeywell,1985.
45.“T8000 performance specifications”,Hommelwerke,2015.