研究生: |
蔡凱全 Kai-cyuan Cai |
---|---|
論文名稱: |
箝位電流模式控制之'CUK功率因數修正器 Clamp Current Mode Control 'CUK Power Factor Corrector |
指導教授: |
羅有綱
Yu-Kang Lo 邱煌仁 Huang-Jen Chiu |
口試委員: |
鄭世仁
none 馬紅波 none |
學位類別: |
碩士 Master |
系所名稱: |
電資學院 - 電子工程系 Department of Electronic and Computer Engineering |
論文出版年: | 2013 |
畢業學年度: | 101 |
語文別: | 中文 |
論文頁數: | 82 |
中文關鍵詞: | 負電壓極性輸出 、' CUK功率因數修正器 、數位用戶線路電源 、箝位電流模式控制法 、電壓隨耦控制法 |
外文關鍵詞: | negative voltage output, ' CUK power factor corrector, DSL power, clamp current mode control, voltage-follower control |
相關次數: | 點閱:238 下載:5 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本論文主要研製一台負電壓極性輸出的交流-直流轉換器,電路拓樸採用'CUK功率因數修正電路轉換器為基礎,利用電路架構本身具有昇降壓特性且輸入與輸出電流為連續,具有低漣波優點。使用UC3842控制,利用箝位電流模式控制法,配合電壓隨耦控制功能特性,來達到功率因數修正之目的。文中並針對其'CUK功率因數修正電路轉換器、箝位電流模式控制法、電壓隨耦控制法及斜率補償等架構做原理分析並加以說明。並利用PSIM模擬軟體進行電路模擬,驗證及確認其設計之可行性。最後設計實作一台100W箝位電流模式控制之'CUK功率因數修正轉換器,將實測結果和理論值相互印證。
This thesis presents an AC-DC converter with negative voltage output. The circuit topology is based on the 'CUK power factor correction converter with inherent voltage step-up/down features. The input and output currents are continuous, low ripple currnet can be achieved. Using UC3842 control IC and the clamp current mode control and voltage-follower control, the studied AC-DC converter has high input power factor. The operating principles for the 'CUK power factor correction converter, clamp current mode control, voltage-follower control, and slope compensation are anlyzed and discussed. Some PSIM simulation results are shown to verify feasibility of the design. An 100W clamp-current-mode control 'CUK power factor correction converter is implemented and tested. The experimental results are fully agreed with the theoretical anlysis.
[1]http://big5.51base.com/electron/adhibition/power/20090326114368.shtml通信系統電源設計
[2]IEC61000-3-2,“Electromagnetic Compatibility(EMC), Part3:Limits Section 2:Limits for harmonic current emissions,”1995.
[3]N. Mohan, T. M. Undeland, and W. P. Robbins,“Power Electronics Converters, Applications and Design,”John Wiley & Sons, 3rd Edition, 2003.
[4]S. Kim and P. N. Enjeti,“A Modular Single-Phase Power Factor Correction Scheme with a Harmonic Filtering Function,”IEEE Transactions on Industrial Electronics, Vol. 50, No. 2, pp.328-335, April. 2003.
[5]A. I. Pressman,“Switching Power Supply Design,”Second Edition, McGraw-Hill International, 1998.
[6]宋自恆、林慶仁,「功率因數修正器之原理與常用元件規格」,新電子科技雜誌217期,民國93年4月。
[7]曾軍皓,「高效能功率因數修正器研製」,國立台灣科技大學電子工程系研究所碩士論文,民國95年。
[8]鍾世彥,「單級高功因LED燈驅動器之研製」,中原大學電機工程學系所碩士論文,民國95年。
[9]O. Busse, S. Mayer, B. Schemmel, and A. Storm,“SEPIC Converter to Perform Power Factor Correction in a Ballast for Fluorescent Lamps,”Industry Applications Conference, 2005. Fourtieth IAS Annual Meeting. Conference Record of the 2005 Volume 4, 2-6 Oct. 2005, pp.2770 – 2774.
[10]J. Chen and C. Chang,“Analysis and Design of SEPIC Converter in Boundary Conduction Mode for Universal-line Power Factor Correction Applications,” Power Electronics Specialists Conference, 2001. PESC. 2001 IEEE 32nd Annual Volume 2, 17-21 June 2001, pp.742 - 747.
[11]H. M. Huang, S. H. Twu, S. J. Cheng, and H. J. Chiu,“Asingle-stage SEPIC PFC Converter for Multiple Lighting LED Lamps,”Electronic Design, Test and Applications, 2008. DELTA 2008. 4th IEEE International Symposium on 23-25 Jan. 2008, pp.15 - 19.
[12]洪瑞鴻,「2kW功率因數修正器研製」,國立台灣科技大學電子工程系研究所碩士論文,民國94年。
[13]林鋒瑋,「單級高功因HID燈高頻電子安定器之研製」,中原大學電機工程學系所碩士論文,民國95年。
[14]Texas Instruments Incorporated,“UC3854 High Power Factor Preregulator,” 1999.
[15]C. A. Canesin and I. Barbi,“Analysis and Design of Constant-Frequency Peak-Current-Controlled High-Power-Factor Boost Rectifier with Slope Compensation,” 1996. APEC '96., Vol. 2, pp. 807-813, March 1996.
[16]M. F. Schlecht and B. A. Miwa,“Active Power Factor Correction for Switching Power Supplies,”IEEE Transactions on Power Electronics, Vol 1. PE-2, No. 4. October 1987.
[17]張家榮,「不需輸入電壓感測之主動型功因修正 AC/DC 轉換器的研製」,國立中山大學電機工程系研究所碩士論文,民國95年。
[18]H. Wei and I. Batarseh,“Comparison of Basic Converter Topologies for Power Factor Correction,”IEEE PESC, pp. 348-353, 1998.
[19]梁適安,「交換式電源供應器之理論與實務設計」,民國83年,全華科技圖書。
[20]陳永錄,「新型Cuk-Sepic轉換器分析與設計」,國立臺灣海洋大學電機工程系研究所碩士論文,民國96年。
[21]顏上進,「生化儀器用電源供應器之研製」,國立台灣科技大學研究所碩士論文,民國91年。
[22]C. Basso,“Ramp Compensation for the NCP1200,”Semiconductor Components Industries, 2001 March, 2001 – Rev. 1.
[23]C. Basso,“Ramp Compensation for Current-Mode Converters,” www.powerelectronics.com, Power Electronics Technology, July 2004.
[24]N. J. Barabas,“Simplified Control Algorithm for Active Power Factor Correction,”In Power Conversion Int. (PCI) Conf. Proc., Oct. 1985, pp.1–9.
[25]D. Maksimovi,“Design of the Clamped-Current High-Power-Factor Boost Rectifier,”In IEEE Applied Power Electronics Conf. (APEC) Proc., Feb.1994, pp. 584–590.
[26]R. Redl and B. R. Erisman,“Low-Cost Power-Factor Correction/ Line Harmonics Reduction with Current-Clamped Boost Converter,”In Power Conversion Proc., June 1995, pp. 229–239.
[27]R. Redl, A. S. Kislovski, and B. P. Erisman,“Input-Current Clamping: An Inexpensive Novel Control Technique to Achieve Compliance with Harmonic Regulations,”In IEEE Applied Power Electronics Conf. (APEC) Proc., Mar. 1996, pp. 145–151.
[28]Texas Instruments Inc,“UC3842 Current Mode PWM Controller,”Data Sheet, June. 2007.
[29]EPARC 著,「電力電子學綜論」,民國96年,全華科技圖書。
[30]S. Basu, M. H. J. Bollen, and T. M. Undeland,“PFC Strategies in light of EN 61000-3-2,”Norwegian University of Science and Technology.
[31]Y. Yuanmao, C. Ka Wai,“Transistor-Diode-Tapped Inductor DC Convertors and the Analysis of Their Characteristics,”IEEE Transactions on Power Electronics, 04. Oct. 2011.