研究生: |
郭庭蓁 Ting-jhen Guo |
---|---|
論文名稱: |
反應性微膠顆粒型抗收縮劑、奈米級核殼型橡膠增韌劑與蒙特納石黏土對苯乙烯/不飽和聚酯/特用添加劑三成份系其聚合固化後成品之微觀型態結構、體積收縮特性及內部可染色性之影響研究 Effects of reactive microgel-based low-profile additives, nano-scale core-shell rubber tougheners, and montmorillonite clay on the morphology, volume shrinkage characteristics and internal pigmentability for styrene/unsaturated polyester/additive ternary systems after the cure |
指導教授: |
黃延吉
Yan-Jyi Huang |
口試委員: |
邱文英
none 陳崇賢 none |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 化學工程系 Department of Chemical Engineering |
論文出版年: | 2006 |
畢業學年度: | 94 |
語文別: | 中文 |
論文頁數: | 211 |
中文關鍵詞: | 反應性微膠顆粒 、核殼型橡膠 、蒙特納石黏土 、不飽和聚酯樹脂 、抗體積收縮劑 、體積收縮 、內部可染色性 |
外文關鍵詞: | reactive microgel particle, core-shell rubber, montmorillonite clay, unsaturated polyester resin, low profile additives, volume shrinkage, internal pigmentability |
相關次數: | 點閱:323 下載:3 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本文之目的,乃探討三種特用添加劑,分別為:(1)反應性微膠顆粒(reactive microgels, RM)型抗收縮劑(LPA)、(2)奈米級核殼型橡膠(core-shell rubber)增韌劑及(3)蒙特納石黏土(montmorillonite clay,MMT),其對苯乙烯/不飽和樹脂/特用添加劑三成份系統,其聚合固化後成品之微觀型態結構、抗體積收縮特性、及內部可染色性之影響。實驗之結果,吾人將配合苯乙烯/不飽和聚酯樹脂/特用添加劑三成份系統在未反應前之相容性,固化樣品之微觀結構、聚合固化後之反應轉化率及微孔洞體積分率等因素之整合性實驗測量結果加以解釋。
The effect of three series of additives, including(1) reactive microgel particle, (2) nano- scale core-shell rubber toughener, and (3) montmori- llonite clay, on the morphology, volume shrinkage characteristics, and internal pigmentability for the styrene(ST)/ unsaturated polyester(UP) /additive ternary systems after the cure were investigated. The experi- mental results have been explained by integrated measurements com- bining phase characteristic of the ST/UP/additive ternary system before the cure, cured sample morphology, final cure conversion, and volume fraction of microvoid generated during the cure.
1. E.J. Bartkus and C.H Kroekel, Appl.Polym.Symp.,15, 113(1970)
2. K.E.Atkins,in”Sheet Molding Compound :Science and Technology”.Ed., H.G. Kia, Hanser Publishers, New York,1993, Ch4.
3. V.A. Pattison, R.R. Hindersinn and W.T. Schwartz,J. Appl.Polym.Sci., 18,2763(1974)
4. V.A. Pattison, R.R. Hindersinn and W.T. Schwartz,J. Appl.Polym.Sci., 19,3045(1975)
5. L. Suspene, D. Fourquier and Y.S. Yang, Polymer,32,1593 (1991)
6. C.P. Hsu, M. Kinkelaar, P. Hu and L.J. Lee. Polym.Eng.Sci., 31, 1450 (1991)
7. Y.J Huang and C.M. Liang, Polymer, 37,401(1996)
8. Y.J. Huang, C.J. Chu, and J.P. Dong, J. Appl. Polym. Sci., 78, 543 (2000)
9. Y.J. Huang, T.S. Chen, J.G. Huang, and F.H. Lee,J.Appl. Polym. Sci., 89, 3336(2003)
10. J.P. Dong, J.G. Huang, F.H. Lee, J.W. Roan,and Y.J. Huang, J.Appl. Polym.Sci.,91,3388(2004)
11. K.E. Atkins and G.C. Rex. 48th Annual Conference, Composite Institute. SPI, Session 6-D (Feb, 8-11,1993)
12. K.E. Atkins and G.C. Rex. , C.G. Reid, R.L. Seats and R.C. Candy, 47th Annual Conference,Composite Institute. SPI, Session 7-D (Feb, 3-6,1992)
13. Y.J. Huang and C.C. Su,J. Appl.Polym.Sci., 55,323(1995)
14. P.W.K. Lam,Polym.Eng. Sci., 29,609(1989)
15. C.B. Bucknall, I.K. Partridge, and M.J. Phillips, Polymer, 32,786(1991)
16. Y.J. Huang and J.C. Horng, Polymer,39,3683(1998)
17. Y.J. Huang and W .C.Jiang, Polymer,39,6631(1998)
18. Y.J. Huang and L.D.Chen, Polymer ,39,7049(1998)
19. Y.J. Huang ,S.C.Lee, and J.P. Dong, J. Appl. Polym.Sci.,78, 558 (2000)
20. E. Martuscelli, P. Musto, G.. Ragosta, G. Scarinzi, and E. Bertotti, J.Polym.Sci., Part B:Polym.Phys.,31,619(1993)
21. S.B. Pandit, and V.M. Nadkarni,Ind. Eng. Chem. Res.,33, 2778 (1994)
22. The B.F. Goodrich Co., WO93/21274(Oct. 28,1993)
23. Crc for Polymers Pty. Ltd., WO97/43339(Nov. 20,1997)
24. Y. Kojima, A. Usuki, M. Kawasumi, A. Okada, T. Kurauchi, and O. Kamigaito, J.Polym.Sci. Part A:Polym.Chem,31,983(1993)
25. X. Kornmann, L.A. Berglund, J. Sterte, and E.P. Giannelis, Polym. Eng. Sci.,38,1351(1998)
26. D.J. Suh, Y.T. Lim, and O.O. Park, Polymer,41,8557(2000)
27. R.K. Bharadwaj, A.R. Mehrabi, C. Hamilton, C. Trujillo, M. Murga, R. Fan, A.Chavira, and A.K. Thompson, Polymer,43,3699(2002)
28. A. Al-Khanbashi, M. El-Gamal, and A. Moet, J. Appl. Polym. Sci., 98, 767(2005)
29. 盧天智,碩士論文,台灣科技大學,1991
30. Y.S. Yang and L.J.Lee, Polymer,29,1793(1988)
31. 蘇進成,碩士論文,台灣科技大學,1992
32. 林立翔,碩士論文,台灣科技大學,1992
33. K.E.Atkins, in “Polymer Blends” ed., D.R.Paul and S.Newman, Academic Press, New York, Vol.2.(1978)
34. Y.J. Huang and C.C. Su, J. Appl. Polym.Sci.,55,305(1995)
35. Y.J. Huang and C.C. Su, Polymer,35,2397 (1994)
36. Y.J. Huang and T.J. Lu and W. Hwu, Polym. Eng. Sci.,33,1 (1993)
37. T. Mitani, H. Shiraishi, K. Honda and G.E. Owen, 44th Annual Conference Composite Institute,SPI,Session 12-F (Feb. 6-9,1989)
38. M.B.C Park and F.J. Mcgarry, 48th Annual Conference , Composite Institute,SPI,Session 12-F(Feb.6-9,1989)
39. 陳立德,碩士論文,台灣科技大學,1996
40. H.J. Sue, E.I. Garciameitin, and D.M. Pickelman, in”Polymer Toughening, Ch. 5”, ed., C.B.Arends, MarcelDekker, New York,1996
41. The Dow Chemical Company, US Patent 4, 778, 851(Oct. 18.1998)
42. J. Y. Qian, R.A. Pearson, V.L. Dimonie, and M.S. El-Aasser, J. Appl. Polym. Sci., 58, 439(1995)
43. K.F. Lin and Y.D. Sheh, J.Appl. Polym. Sci., 69, 2069(1998)
44. K.F. Lin and Y.D. Shieh, J.Appl. Polym. Sci., 70, 2313(1998)
45. P.Hazot, C.Pichot, and A. Maazouz, Macromol. Chem. Phys., 201, 632(2000)
46. W. Funke, R.Kolitz,and W. Straehle, Makromol. Chem. ,180, 2797 (1979).
47. W. Funke, Br. Polym J., 21, 107, (1989).
48. Y. Hoshino, K. Kataoka, Y. Asanaka, and H.Takeuchi, 46th Ahnual Conference. Composite Insitute, SPI, Session 21-A(Feb.1991).
49. 梁繼文, “礦物學(下)”, 台北市, 五南圖書, 1984.
50. W. E. Worrall, “Clays and Caramic Raw Materials,” 2nd Ed, Elsevier, London, 1986.
51. T. Lan and T. J. Pinnavaia. Chem. Mater., 6, 2216(1994)
52. 蔡明洲,碩士論文,台灣科技大學,2006
53. 陳銘琦,碩士論文,台灣科技大學,2006
54. 百康奈米科技股份有限公司產品目錄
55. Southen Clay Product, Inc.產品Data sheet.
56. Shengpei Su and Charles A. Wilkie, J. Polym. Sci.: Part A: Polym. Chem., 41, 1124(2003)
57. 梁景冠,碩士論文,台灣科技大學,2003
58. 陳紹偉,碩士論文,台灣科技大學,2004
59. 廖萬達,碩士論文,台灣科技大學,2005
60. 楊逸璇,碩士論文,台灣科技大學,2006