研究生: |
蔡承昀 Cheng-Yun Tsai |
---|---|
論文名稱: |
梁柱交接處連接版對鋼結構梁柱接頭行為之影響 The effect of the behavior on gusset plate of steel beam-column joints |
指導教授: |
陳正誠
Cheng-Cheng Chen |
口試委員: |
陳誠直
none 黃世建 none |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 營建工程系 Department of Civil and Construction Engineering |
論文出版年: | 2005 |
畢業學年度: | 93 |
語文別: | 中文 |
論文頁數: | 65 |
中文關鍵詞: | 切削 、鋼結構 、斜撐連接板 、梁柱接頭 |
外文關鍵詞: | shaving, gusset plate |
相關次數: | 點閱:153 下載:8 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本研究主要在探討斜撐構架之梁柱接頭讀應力傳遞行為,視其銲接方式是否妥當,就工地現有的梁柱接頭切削方式做分析與建議,並配合ANSYS有限元素法分析軟體證明。本實驗共有四支梁柱接頭試體進行反覆載重試驗,針對其應力傳遞過程,推求其剛性區域(rigid zone) 產生的位置,及其塑性轉角容量。依照實驗結果可得到結論如後:
(1) 腹板加勁板使用填角銲已足夠提供所需的強度。 (2) 單邊斜撐塑角可視為產生於梁下翼板處。 (3) 斜撐連接板可增加塑性轉角容量。(4) 雙邊斜撐臨界斷面為鋼梁腹板加勁板處。(5) 螺栓接合於試體臨界面之斜撐梁柱接頭,塑性轉角容量與傳統梁柱接頭之塑性轉角容量大致相同。(6) 切削於連接板之外,其塑性轉角即可達到規範規定之塑性轉角容量。
The aim of this study is to discuss how the stresses transfer in beam-column joints with gusset plate and make a suggestion for shaving the beam flange in order to improve rotation demand. Four beam-column joint specimens were tested to failure by cyclic loading. Non-linear finite element method is be used to compare with experimental results and presume the length of rigid zone and the plastic rotation capacity. Base on the experimental and analytical results, following conclusions can be drawn. (1) Fillet welds is sufficient for web stiffness plate. (2) The plastic rotation point of beam-column joint with single gusset plate occurs at bottom flange. (3) Gusset plate can improve plastic rotation capacity. (4) The plastic rotation point of beam-column joint with double gusset plate occurs at web stiffness plate. (5) The plastic rotation capacity can be improve by shaving at the flange.
1.陳清泉『榮總大樓更新計畫第二期醫療大樓工程鋼結構之接頭韌性試驗』,台灣營建研究中心,民國七十四年十二月。
2.陳生金,楊榮坤,『箱型柱與樑接頭之耐震行為』國科會研究報告,NSC78-0414-P011-0113。
3.陳光凱,『鋼樑與箱型柱行為研究』,碩士論文,國立台灣工業技術學院工程技術研究所。台北(1991)。
4.林佳煜,『銲接孔對梁柱接頭耐震行為之影響』,碩士論文,國立科技大學營建工程系,台北(2001)。
5.ATC-24
6.李心弘,『含普通強度鋼材之韌性斜撐構材之遲滯與損傷模式』,碩士論文,國立科技大學營建工程系,台北(2004)。
7.洪沛甫,『鋼筋混凝土內部梁柱接頭耐震設計與配筋細則之研究』,碩士論文,國立科技大學營建工程系,台北(2003)。