研究生: |
柯定成 Ting-chen Ko |
---|---|
論文名稱: |
大型滑蓋之結構分析與尺寸參數設計 Structure Analysis and Parameter Design of Large-scale Slide Hinge |
指導教授: |
林清安
Ching-An Lin |
口試委員: |
鄭逸琳
Yih-Lin Cheng 賴景義 Jiing-Yih Lai |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2010 |
畢業學年度: | 98 |
語文別: | 中文 |
論文頁數: | 113 |
中文關鍵詞: | 大型滑蓋 、參數設計 、田口法 |
外文關鍵詞: | Large-scale Slide Hinge, Pro/E Mechanism, Parameter Design |
相關次數: | 點閱:490 下載:9 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
大尺寸3C產品的滑蓋結構應用在市面上較少見,本研究主要討論如何利用Pro/E Mechanism建立一套分析模型,以模擬手機滑蓋的運動方式與受力情形,並將此分析模型套用在大型滑蓋結構上做設計驗證,最後以田口法為基礎進行最佳化設計,以求得大型滑蓋結構在可運作前提下的最小推力。
本論文主要分成三個部份:
1.以Pro/E Mechanism為動態模擬與分析工具,針對質量屬性、連接條件、彈簧、摩擦力與負載,完成分析所需的設定,以建立一套實用的分析模型。
2.利用這套分析模型模擬手機滑蓋結構,並將模擬結果與實測值互相比較以檢視其準確度,透過幾個重要設計參數的變更,來驗證模擬結果的合理性。
3.將此分析模組套用在大型滑蓋的3D CAD model上做動態模擬與受力分析,選擇4個重要設計尺寸,透過田口法找出最佳化的尺寸組合,以求得滑蓋結構的最小推力,提供研發人員設計時的參考。
The application of a sliding hinge for large-scale 3C products is not common in the current market. In this thesis, the Mechanism module of Pro/ENGINEER was used to simulate the motion and dynamic behaviors of the sliding hinge in mobile phones, and was later applied to a large-scale sliding hinge. The Taguchi method was also used as the foundation for an optimal design to determine the minimum pushing force for a large-scale sliding hinge under functional conditions.
The thesis consists of three parts:
1.Used the Mechanism module of Pro/ENGINEER as the tool for motion simulation and dynamic analysis. Focused on the settings of mass properties, connections, springs, friction and loads to develop a feasible analysis model.
2.Used the analysis model to simulate the structure of a sliding hinge, and compared simulation results with experimental data for validation. The values for certain key design parameters were varied to confirm the simulated results.
3.Applied the analysis model to the 3D CAD model of a large scale sliding hinge and performed motion simulation and dynamic analysis. Four key dimensions were selected and the Taguchi method was used to determine the optimal combination of these dimensions to achieve minimal pushing force the slide hinge. This can serve as a reference for designers during the development of mobile phones.
1.劉晉奇,褚晴暉,有限元素分析與ANSYS的工程運用,滄海書局,台北,2006。
2.蔡意輝,「滑蓋彈簧之壽命分析」,台灣科技大學碩士論文,2009。
3.張敬民,「應用基因演算法於滑蓋手機彈簧結構最佳化設計」,高雄第一科技大學碩士論文,2009。
4.陳盈璋,「滑蓋彈簧應力分析與尺寸參數設計」,台灣科技大學碩士論文,2007。
5.馬揚傑,「扭力彈簧之電腦輔助應力分析」,國立臺灣科技大學機械工程研究所碩士論文,2009。
6.林明璋,「滑蓋手機之機構研究」,逢甲大學碩士論文,2007。
7.楊之青,「行動電話外殼卡勾之CAE分析」,台灣科技大學碩士論文,2005。
8.陳古峰,「PC伺服器之Pro/Engineer結構分析」,台灣科技大學碩士論文,2008。
9.林弘宗,「泛用型自動插件機之結構分析及改進設計」,淡江大學碩士論文,2000。
10.楊忠衡,「PCB鑽孔機進給系統之分析與設計」,彰化師範大學碩士論文,2000。
11.許時瑋,「液化石油氣槽車安全連接器之設計」,淡江大學碩士論文,1999。
12.李輝煌,田口方法:品質設計的原理與實務,高立圖書有限公司,台北,2008。
13.Peace, G. S., Taguchi Methods: a Hands-on Approach, Addison-Wesley Publishing Company, Inc., Boston, Massachusetts, 1992.
14.Tsui, K. L., “Modeling and Analysis of Dynamic Robust Design Experiments”, IIE Transactions, 31, p. 1113-1122,1999.
15.Antony, J., “Simultaneous Optimization of Multiple Quality Characteristics in Manufacturing Processes Using Taguchi’s Quality Loss Function”, International Journal of Advanced Manufacturing Technologies, Vol. 17, 2001, pp. 134-8.
16.林清安,Pro/ENGINEER Wildfire 2.0 零件組立與產品設計,知城數位科技股份有限公司,台北,2004。
17.林清安,Pro/ENGINEER野火3.0動態機構設計與模擬,旗標出版股份有限公司,台北,2006。