簡易檢索 / 詳目顯示

研究生: 董宜鑫
Yi-Hsin Tung
論文名稱: 考慮鋼筋腐蝕區位影響之梁桿件耐震行為分析
Study on Pitting Corrosion Effects on Seismic Behavior of Corroded RC Beams
指導教授: 邱建國
Chien-Kuo Chiu
口試委員: 陳瑞華
Ruei-Hua Chen
廖文義
Wun-Yi Liao
蕭輔沛
Fu-Pei Hsiao
學位類別: 碩士
Master
系所名稱: 工程學院 - 營建工程系
Department of Civil and Construction Engineering
論文出版年: 2014
畢業學年度: 102
語文別: 中文
論文頁數: 128
中文關鍵詞: 二維桁架模型鋼筋腐蝕強度極限性能點
外文關鍵詞: Two-dimension lattice model, corroded reinforcement strength, ultimate performance
相關次數: 點閱:205下載:22
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

本論文採用SAP2000分析軟體建立二維桁架模型,主要目的為探討鋼筋腐蝕梁二維桁架模型分析之可行性研究,將分析求得之力與位移關係曲線與足尺寸實驗結果進行比較討論。依主筋腐蝕、主筋箍筋腐蝕及箍筋腐蝕三種不同鋼筋腐蝕區位建模,模型之斷面積與實體結構有關,鋼筋混凝土材料性質是依照文獻經驗公式與實驗之混凝土抗壓強度、鋼筋降伏強度及腐蝕重量減少率等參數求得,可依照鋼筋腐蝕區域給予參數並匯入模型中,分析後再考慮撓曲握裹及錨定握裹破壞以決定曲線之極限性能點,最後,以降伏力量比、勁度比及極限應變比驗證二維桁架模型之可行性。


The main purpose of this study is to discuss the application and the feasibility of the two-dimensional lattice model of the corroded reinforced concrete beams, which is built by the analysis software SAP2000. There are corroded reinforcement models, corroded reinforcement and stirrup models, and corroded stirrup models to obtain the curve of force-displacement from analysis which compared with the results from the full-size experiment. The compressive strength, yielding strength, and percentage of the corroded weight reduction and so on are from the experienced formula. According to the corroded region, the parameters can import into the model, and then decide the curve of the point of ultimate performance by flexure bonding and anchoring bonding. Finally, by using yielding ratio, stiffness ratio, and ultimate strain ratio to prove the feasibility of the two-dimension lattice model.

第一章 緒論 1.1 前言 1.2 研究方法 1.3 論文架構 第二章 文獻回顧 2.1 二維桁架模型之求解方程式 2.2 材料性質介紹 2.2.1 Mander混凝土抗壓模型 2.2.2 Mander無圍束混凝土抗壓模型 2.2.3 Fukuura鋼筋模型 2.2.4 Okamura與Maekawa混凝土模型 2.3 腐蝕之形成 2.3.1 腐蝕對材料性質之影響 2.3.2 腐蝕率滑移理論 2.3.3 腐蝕梁之撓曲行為 2.4 裂縫與鋼筋腐蝕之循環關係 2.5 鋼筋腐蝕對梁構件耐震行為之影響 2.6 軟化壓拉桿之基本模型與理論介紹 2.6.1 混凝土軟化效應 2.6.2 混凝土軟化係數 2.6.3 鋼筋腐蝕對保護層混凝土抗壓強度與韌性之影響 2.7 箍筋腐蝕模型分析結果 2.7.1 二維桁架模型網格細度分類 2.7.2 箍筋分析結果比較 2.8 SAP2000元素介紹 第三章 鋼筋混凝土梁之二維模型分析 3.1 二維桁架一般模型之建立流程 3.1.1 模型之建立流程 3.1.2 桿件名稱與配置 3.1.3 桿件材料性質 3.1.4 桿件斷面積 3.2 二維桁架鋼筋腐蝕模型之建立流程 3.2.1 主筋腐蝕模型 3.2.2 箍筋腐蝕模型 3.3 二維桁架模型分類 第四章 試體參數介紹及材料參數 4.1 實驗試體參數介紹 4.1.1 足尺寸腐蝕梁試驗 4.1.2 鋼筋量測之計算公式 4.2 鋼筋腐蝕前後直徑(面積)紀錄 4.2.1 縱向鋼筋 4.2.2 橫向鋼筋 4.3 材料性質 4.3.1 混凝土材料性質 4.3.2 鋼筋材料性質 4.3.3 腐蝕模型之材料性質 4.4 軟體SAP2000建立模型流程 第五章 二維桁架模型分析與實驗結果比較探討 5.1 二維桁架模型分析與實驗結果比較探討 5.1.1 主筋腐蝕、箍筋未腐蝕梁之二維模型分析結果(B) 5.1.2 主筋腐蝕、箍筋腐蝕梁之二維模型分析結果(A) 5.1.3 主筋未腐蝕、箍筋腐蝕梁之二維模型分析結果(C) 5.2 勁度比、極限位移比及降伏力比之比較探討 第六章 結論與建議 參考文獻

1. Mander, J. B., Priestley, M. J. N., and Park, R., ASCE.1988.“Theoretical Stress-Strain Model for Confined Concrete”Journal of Structural Engineering, Vol. 114, No. 8, pp.1804-1826.
2. Okamura, H. and Maekawa, K.,.1991. “Nonlinear Analysis and ConstitutiveModels of Reinforced Concrete”, Gihodo Publication.
3. Fukuura, N. and Maekwa, K., .1997. “Computational Model of reinforcingBar under Reversed Cyclic Loading for RC Nonlinear Analysis,”Journal of Materials, Concrete Structures and Pavements, JSCE, No.564/V-35, pp.291-295.
4. 規範FEMA356,2000年,"Prestandard and Commentary for the Seismic Rehabilitation of Buildings."
5. 李秉乾,詹勳源,2004年,“含牆RC構架極限軟化桁架模型分析研究”,逢甲大學土木工程學系碩士論文。
6. 王勇智,徐鍇,2007年,“以桁架模式分析鋼筋混凝土抗彎構架行為之研究”國立中央大學土木工程研究所碩士論文。
7. 金螢來,2008年,“An Evaluation Study on the Degradation of the Load-bearing Capacity by the Rebar Corrosion in Reinforced Concrete Structures.”東京大學。
8. 中國土木水利工程學會,2009年,“鋼筋混凝土學(土木406-98)”科技圖書公司,台北市,台灣。
9. 邱建國,王儒祥,2011年,“鋼筋腐蝕梁二維桁架分析模型之可行性研究”,國立台灣科技大學營建工程研究所碩士論文。
10. 歐昱辰,陳厚亨,2011年,“含腐蝕橫向鋼筋之鋼筋混凝土梁耐震行為”,國立台灣科技大學營建工程研究所碩士論文。
11. ACI. 2011. Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute (Committee 318), Farmington Hills.
12. 邱建國,林宜鋒,2012年,“劣化RC建築物生命週期維護管理決策支援系統”,國立台灣科技大學營建工程研究所碩士論文。
13. 邱建國,莊育泰,2012年,“劣化RC牆生命週期耐震能力研究”,國立台灣科技大學營建工程研究所碩士論文。
14. 歐昱辰,卓奕杉,2012年,“RC梁鋼筋腐蝕之剪力行為評估與縱向鋼筋腐蝕之耐震行為”,國立台灣科技大學營建工程研究所碩士論文。
15. 歐昱辰,葉勁宏,2013年,“梁主筋腐蝕位置對桿件韌性行為之研究”,國立台灣科技大學營建工程研究所碩士論文。

QR CODE