研究生: |
李維堂 Wei-tang Lee |
---|---|
論文名稱: |
側吹式散熱器之熱傳性能分析 Investigations on heat transfer performance of side blow coolers |
指導教授: |
洪俊卿
Jin-Tsing Hong |
口試委員: |
林顯群
Sheam-Chyun Lin 孫珍理 Chen-Li Sun |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2009 |
畢業學年度: | 97 |
語文別: | 中文 |
論文頁數: | 145 |
中文關鍵詞: | 側吹式散熱器 、散熱片 、田口方法 |
外文關鍵詞: | Side blow coolers, Taguchi method, Heat sink |
相關次數: | 點閱:299 下載:5 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
散熱問題是影響晶片效能可否提升及系統穩定性的關鍵因素,而散熱器即扮演著加快晶片散熱速度的角色,本研究是針對氣冷式的電子散熱裝置,即散熱片與風扇的組合,以數值模擬配合田口分析,進行散熱片的熱傳性能分析。首先定義散熱片之設計參數,以一維解析方法計算散熱片的熱阻及壓降,評估所配置的參數是否符合本研究所設定的效能目標,接著使用熱傳分析軟體FLOTHERM進行散熱片效能模擬。此外本研究也實際製作樣品,利用實驗測量的結果來比對解析方法及數值模擬結果。
根據研究中配置的設計參數,在田口方法分析後得到影響散熱片熱阻程度大小的設計參數為:鰭片的數目>鰭片的厚度>鰭片的高度>底座厚度;影響散熱片壓降程度大小的設計參數為:鰭片厚度>鰭片數目>鰭片高度>底座厚度。
本研究的分析方法及結果,可提供設計者在進行散熱片的開發設計時,能以較低的實驗操作成本和較短的分析時間,得到最佳的散熱片設計參數組合。
The effectiveness of the heat-dissipation module is a critical factor which affects the reliability and the operation of an electronic device. This study employed the Taguchi method to find the optimal design parameters for the active air-chilled heat sink device. The heat transfer and fluid flow characteristics are studied using one-dimensional analytic thermal resistance network model, three-dimensional CFD model and experimental methods
The commercially available FLOTHERM software was chosen as the tool to make the CFD study. The comparison of the results shows satisfactory agreement between the results obtained by different study methods.
Fours different design parameters: the thickness of the base plate, the thickness of the fin, the height of the fin, and the total number of the fin, are chosen to study their effect on the heat sink thermal performance. It is found that the two most important factors that affect the pressure drop and thermal performance characteristics of the heat sink are the thickness of the fin and the total number of fins of the heat sink. Base on the Taguchi method, an optimal design of the heat sink is proposed and its performance is confirmed by the experimental measurement.
[1] 王啓川,一些氣冷式散熱鰭片應用於電子散熱之基本觀念,工業材料,頁133-143,民94年。
[2] Balanced Technology Extended (BTX) System Design Guide Version 1.1 February 2007.
[3] D. R. Haper, and W. B .Brown, "Mathematical Equations for Heat Conduction in the Fins if Air Cooled Engines," NACA Report No.158, 1922.
[4] M. N. Murray, "Heat Transfer Through an Annular Disk or Fin of Uniform Thickness," Trans. ASME, J. Applied Mech., 60, A78, 1938.
[5] S. Lee, "Optimum design and selection of heat sinks," IEEE Transactions on Components and Packaging and Manufacturing Technologies, pp. 812-817, 1995.
[6] S. Lee, "Calculating spreading resistance in heat sinks," Electronics Cooling, Vol.4,No.1, pp. 30-33, January 1998.
[7] K. Azar, R. S. McLeod, and R. E. Caron, "Narrow Channel Heat Sink for Cooling of High Powered Electronic Components, " in Proc. 8th Annual. IEEE Semi-Therm Symp., pp. 12–19,1992.
[8] R. E. Simons, "Estimating Parallel Plate-Fin Heat Sink Pressure Drop," Electronics Cooling, Vol. 9, No.2, pp. 8–10, May 2003.
[9] J. R. Culham, and Y. S. Muzychka, "Optimization of Plate Fin Heat Sinks Using Entropy Generation Minimization," IEEE Trans. Components and Packaging Technologies, Vol. 24, No.2, pp. 159-165, 2001.
[10] R. W. Knight, J. S. Goodling, and D. J. Hall, "Optimal Design of Forced Convection Heat Sinks—Analytical," ASME J. Electron. Packaging, vol. 113, pp. 313–321, 1991.
[11] A. R. Wirtz, W. Chen, and R. Zhou, "Effect of Flow Bypass
on the Performance of Longitudinal Fin Heat Sinks," ASME
J. Electronic Packaging, Vol. 116, pp. 206-211, 1994.
[12] R. E. Simons, and R. R. Schmidt, "A Simple Method to
Estimate Heat Sink Air Flow Bypass," Electronics Cooling vol.3.No.2, 1997.
[13] 楊愷祥、黃仁傑、曲維信、陳英洋、簡國祥、王啟川,旁通效應對鰭片壓降及熱傳性能影響,熱管理產業通訊,第八期,2007年。
[14] 孫珍理,熱傳學,國立台灣科技大學,數位教材。
[15] 莊嘉琛、劉國祥,電腦用高效能可撓性散熱片節能研究,經濟部能源局技術 節 報 導,第五十期,2003年。
[16] 李輝煌,田口方法-品質設計的原理與實務,高力圖書有限公司,2000。
[17] Intel Nehalem-EP Processor, Electrical, Mechanical, and Thermal Specifications (EMTS), December 2008.
[18] J. R. Culham, W. A. Khan, M. M. Yovanovich, and Y. S. Muzychka, "The Influence of Material Properties and Spreading Resistance in the Thermal Design of Plate Fin Heat Sinks," 35th National Heat Transfer Conference, 2001.
[19] 張志新,放射狀鰭片散熱器之數值模擬與參數探討,國立台灣科技大學機械工程研究所碩士學位論文,2003。
[20] M. M. Yovanovich, J. R. Culham, and P. Teertstra,
"Calculating Interface Resistance," Electronics
Cooling vol.3.No.2, 1997.
[21] 洪英輝、楊安石編譯,電子裝備系統熱傳分析,全華出版社,1987。
[22] S. V. Patankar, "Numerical Heat Transfer and Fluid Flow,"
Hemisphere, Washington, D.C., 1980.
[23] Intel Enterprise System Design Conference-Taipei, April 2008.