研究生: |
林保賢 Pao-Hsien Lin |
---|---|
論文名稱: |
製備錠狀氧化鐵載氧體擔載氧化鋁及二氧化鈦惰性載體並應用於化學迴圈燃燒與產氫之探討 Preparation of Al2O3 and TiO2 Supported Fe2O3 Pellets for Chemical Looping Combustion and Hydrogen Generation |
指導教授: |
顧洋
Young Ku |
口試委員: |
蔣本基
Pen-Chi Chiang 曾堯宣 Yao-Hsuan Tseng 郭俞麟 Yu-Lin Kuo 曾迪華 Dyi-Hwa Tseng |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 化學工程系 Department of Chemical Engineering |
論文出版年: | 2013 |
畢業學年度: | 101 |
語文別: | 英文 |
論文頁數: | 155 |
中文關鍵詞: | 化學迴圈燃燒程序 、載氧體 、澱粉含量 、鐵離子擴散 、產氫 |
外文關鍵詞: | Chemical looping combustion, oxygen carrier, starch content, iron cations diffusion, H2 generation |
相關次數: | 點閱:260 下載:0 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本研究之主要目的為製備適合化學迴圈程序與應用於產氫之鐵系複合載氧體。為了製備具有高機械強度之複合載氧體,分別將氧化鐵與氧化鋁和二氧化鈦混合,並利用壓錠方式製備成錠材。研究結果發現鐵鋁複合載氧體及鐵鈦複合載氧體分別在鍛燒溫度1300 oC與1100 oC下,具有相當好的機械強度與反應性。本研究為了增加錠狀鐵系複合載氧體之反應性,添加不同比例澱粉含量,其研究結果發現隨著澱粉含量增加,鐵鋁複合載氧體的轉化率會逐漸上升,但是鐵鈦複合載氧體的轉化率幾乎不受到澱粉含量增加而有所影響。當鐵鋁複合載氧體之澱粉含量為10 wt%時及鐵鈦複合載氧體之澱粉含量為0 wt%時,皆具有相當不錯的反應性與機械強度,但是經過20圈的氧化還原操作後,鐵鈦複合載氧體之機械強度會有所下降。此外,在20圈的氧化還原後,錠狀複合載氧體表面皆觀察不到惰性載體,其推測為在氧化過程中鐵離子會向外擴散與外部氧離子反應形成氧化鐵進而覆蓋惰性載體,導致在多次氧化還原後,錠狀載氧體表面皆觀察不到惰性載體。
本研究亦將鐵鋁複合載氧體與鐵鈦複合載氧體分別置入固定床反應器進行產氫測試,實驗結果顯示鐵鋁複合載氧體之產氫量是鐵鈦複合載氧體的1.13倍,鐵鈦複合載氧體在多次與水氣氧化後與反應器會有燒結的情況發生,因此可推論鐵鋁複合載氧體為一具有良好反應性與產氫能力的載氧體之一。
Preparation of Fe-based oxygen carriers with support materials as pellets for CLP and hydrogen production was investigated in this study. In order to increase the mechanical strength of carriers, Fe2O3 oxygen carriers were prepared with Al2O3 and TiO2 as inert support with mass ratio of 60/40 by mechanical mixing and pelletized by tablet machine, respectively. The results showed that FeAl320 pellet sintered at 1300 oC had proper mechanical strength and good reactivity. Besides, the FeTi320 pellet sintered at 1100 oC also exhibited adequate mechanical strength and great reactivity.
For increasing reactivity of FeAl320 pellet and FeTi320 pellet, different starch content was added to the pellets. It revealed that the conversion was increased with increasing starch of FeAl320 pellet and the starch was no effect on FeTi320 pellet. However, FeAl320-S10 and FeTi320-S0 pellet showed reasonable reactivity, but mechanical strength of FeAl320-S10 pellet exhibited better than FeTi320-S0 pellet after 20 redox cylces. Furthermore, both of 20 redox cycles FeAl320 pellet and FeTi320 pellet, it was no observed the support materials on the pellet surface of oxygen carriers. It could be possibly suggested that the iron cations may diffuse onto the surface of oxygen carriers and react with oxygen anions during the oxidation period.
Comparison the H2 productions between FeAl320-S10 pellet and FeTi320-S0 pellet, it could be obviously observed that the amount of H2 production of FeAl320-S10 pellet is 1.13 times as large as FeTi320-S0 pellet. However, it would be clearly observed the FeTi320-S0 pellet could be sintered together and agglomerated to wall of fixed bed reactor after multi-steam oxidation cycle. As the above results, it could be summarized that FeAl320-S10 pellet has proper reactivity and has good H2 production at 900 oC and FeAl320-S10 pellet could be a suitable candidate of H2 production for CLP.
Abad, A., Adanez, J., Cuadrat, A., Garcia-Labiano, F., Gayan, P. and de Diego, L.F. “Kinetics of Redox Reactions of Ilmenite for Chemical-Looping Combustion,” Chem. Eng. Sci., Vol. 66, pp. 689-702 (2011).
Adanez, J., de Diego, L.F., Garcia-Labiano, F., Gayan, P. and Abad, A. “Selection of Oxygen Carriers for Chemcial-Loopong Combustion,” Energy Fuels, Vol. 18, pp. 371-377 (2004).
Adanez, J., Dueso, C., de Diego, L.F., Garcia-Labiano, F., Gayan, P. and Abad, A. “Methane Combustion in a 500 Wth Chemical-Looping Combustion System Using an Impregnated Ni-based Oxygen Carrier,” Energy Fuels, Vol. 23, pp. 130-142 (2009).
Adanez, J., Cuadrat, A., Abad, A., Gayan, P., de Diego, L.F. and Garcia-Labiano, F. “Ilmenite Activation during Consecutive Redox Cycles in Chemical-Looping Combustion,” Energy Fuels, Vol. 24, pp. 1402-1413 (2010).
Adanez, J., Abad, A., Garcia-Labiano, F., Gayan, P. and de Diego, L.F. and “Progress in Chemical-Looping Combustion and Reforming Technologies,” Prog. Energy Combust. Sci., Vol. 38, pp. 215-282 (2012).
Albano, M.P., Garrido, L.B., Plucknett, K. and Genova, L.A. “Processing of Porous Yttria-Stabilized Ziconia Tapes: Influence of Starch Content and Sintering Temperature,” Ceram. Int., Vol. 35, pp. 1978-1791 (2009).
Almeida, F.A., Botelho, E.C., Melo, F.C.L., Campos, T.M.B. and Thim, G.P. “Influence of Cassava Starch Content and Sintering Temperature on the Alumina Consolidation Technique,” J. Eur. Ceram. Soc., Vol. 29, pp. 1587-1594 (2009).
Cao, Y. and Pan, W.P. “Investigation of Chemical Looping Combustion by Solid Fuels. 1. Process Analysis,” Energy Fuels, Vol. 20, pp. 1836-1844 (2006).
Cho, P., Mattisson, T. and Lyngfelt, A. “Defluidization Conditions for a Fluidized Bed of Iron Oxide-, Nickel Oxide-, and Manganese Oxide- Containing Oxygen Carriers for Chemical-Looping Combustion,” Ind. Eng. Chem. Res., Vol. 45, pp. 968-977 (2006).
Chen, S., Shi, Q., Xue, Z., Sun, X. and Xiang, W. “Experimental Investigation of Chemical-Looping Hydrogen Generation using Al2O3 or TiO2-Supported Iron Oxides in a Batch Fluidized Bed,” Int. J. Hydrog. Energy, Vol. 45, pp. 968-977 (2006).
Cuadrat, A., Abad, A., Garcia-Labiano, F., Gayan, P., de Diego, L.F. and Adanez, J. “Ilmenite as Oxyhen Carrier in a Chemical Looping Combustion System with Coal,” Energy Procedia, Vol. 4, pp. 362-369 (2011).
Fan, L.S. “Chemical Looping System for Fossil Energy Conversions,” John Wiley & Sons, Inc., New York (2010).
Figueroa, J.D., Fout, T., Plasynski, S., Mcilvried, H. and Srivastava, R.D. “Advances in CO2 Capture Technology-The U.S. Department of Energy’s Carbon Sequestration Program,” Int. J. Greenh. Gas Control, Vol. 2, pp. 9-20 (2008).
Garrido, L.B., Albano, M.P., Plucknett, K. and Genova, L. “Effect of Starch Filler Content and Sintering Temperature on the Processing of Porous 3Y-ZrO2 Ceramics,” J. Mater. Process. Technol., Vol. 209, pp. 590-598 (2009).
Gayan, P., Pans, M.A., Ortiz, M., Abad, A. and de Diego, L.F. “Testing of Highly Reactive Impregnated Fe2O3/Al2O3 oxugen carrier for a SR-CLC System in a Continuous CLC Unit,” Fuel Process. Technol., Vol. 96, pp. 37-47 (2012).
Gennari, F.C., Gamboa, J.J.A. and Pasquevich, D.M. “Formation of Monoclinic Fe2TiO5 in the Fe2O3(s)-TiO2(s)-Cl2(g) System,” J. Mater. Sci. Lett., Vol. 17, pp. 697-700 (2012).
Hossain, M.M. and de Lasa, H.I. “Chemical-Looping Combustion (CLC) for Inherent CO2 Separations-a review,” Chem. Eng. Sc, Vol. 96, pp. 37-47 (2012).
Hurst, S. “Production of Hydrogen by the Steam-Iron Method,” Oil & Soap (1939).
Johansson, M., Mattisson, T. and Lyngfelt, A. “Investigation of Fe2O3 with MgAl2O4 for Chemical-Looping Combustion,” Ind. Eng. Chem. Res., Vol. 43, pp. 6978-6987 (2004).Kierzkowska, A.M., Bohn, C.D., Scott, S.A., Cleeton, J.P., Dennis, J.S. and Muller, C.R. “Development of Iron Oxide Carriers for Chemical Looping Combustion Using Sol-Gel,” Ind. Eng. Chem. Res., Vol. 49, pp. 5383-5391 (2010).
Lane, H. “Process for the Production of Hydrogen,” U.S. Patent, No.664,809 (1939).
Leion, H., Lyngfelt, A., Johansson, M., Jerndal, E. and Mattisson, T. “The Use of Ilmenite as an Oxygen Carrier in Chemical-Loopong Combustion,” Chem. Eng. Res. Des., Vol. 86, pp. 1017-1023 (2008).
Lewis, W.K., Gilliland, E.R. and Mcbride G.T., JR. “Gasification of Carbon by Carbon Dioxide in Fluidized Powder Bed,” J. Ind. Eng. Chem., Vol. 41,No. 6, pp. 1213-1226 (1949).
Li, F., Kim, H.R., Seidhar, D., Wang, F., Zeng, L., Chen, J. and Fan, L.S. “Syngas Chemcial Looping Gasification Process: Oxygen Carrier Particle Selection and Performance,” Energy & Fuels, Vol. 23, pp. 4182-4189 (2009).
Mattisson, T. and Lyngfelt, A. “Capture of CO2 Capture Using Chemical-Looping Combsution,” First Biennial Meeting of the Scandinavin-Nordic Section of the Combustion Institute, Goteborg, Sweden, April (2001).
Mattisson, T. and Lyngfelt, A. “Application of Chemical-Looping Combustion with Capture of CO2,” Second Nordic Minisymposium on Carbon Dioxide Capture and Storage, Goteborg, Sweden, October (2001).
Mattisson, T., Johansson, M. and Lyngfelt, A. “Multicycle Reduction and Oxidation of Iron Oxide Particles-Application to Chemical-Looping Combustion,” Energy Fuels, Vol. 18, pp. 628-637 (2004).
Messerschitt, A. “Process of Macking Hydrogen,” U.S. Patent, No.772,785 (1913).
Ortiz, M., Gayan, P., de Diego, L.F., Garcia-Labiano, F., Abad, A., Pans, M.A. and Adanez, J. “Hydrogen Production with CO2 Capture by Coupling Steam Reforming of Methane and Chemical-Looping Combustion: Use of an Iron –basd Waste Product as Oxygen Carrier Buring a PSA Tail Gas,” J. Power Sources, Vol. 196, pp. 4370-4381 (2011).
Pena, J.A,, Lorente, E. and Herguido, J. “Steam-Iron Process for Hydrogen Production: Recent Advances,” Proceedings WHEC2010, Essen, Germany, May (2010) pp. 319-321.
Rahaman, M.N. “Sintering of Ceramics,” John & Franics Group, New York (2007).
Reddy, S. and Vyas, S. “Recovery of Carbon Dioxide and Hydrogen from PSA Tail Gas,” Energy Procedia, Vol. 1, pp.149-154 (2009).
Riemer, P. “Greenhouse Gas Mitigation Technologies, an Overview of the CO2 Capture, Storage and Future Activities of the IEA Greenhouse Gas R&D programme,” Energy Conv. Manag., Vol. 37, pp.665-670 (1996).
Ryden, M., Lyngfelt, A. and Mattisson, T. “Synthesis Gas Generation by Chemical-Looping Reforming in a Continuously Operating Laboratory Reactor,” Fuel, Vol. 85, pp.1631-1641 (2006).
Ryden, M. and Lyngfelt, A. “Using Steam Reforming to Produce Hydrogen with Carbon Dioxide Capture by Chemical-Looping Combustion,” Int. J. Hydrog. Energy, Vol. 31, pp.1271-1283 (2006).
Ryden, M. and Arjmand, M. “Continuous Hydrogen Production via the Steam-Iron Reaction by Chemical Looping in a Circulating Fluidized-Bed Reactor,” Int. J. Hydrog. Energy, Vol. 37, pp.4843-4854 (2012).
Sun, Z., Zhou, Q. and Fan, L.S. “Reactive Solid Surface Morphlogy Variation via Ionic Diffusion,” Langmuir, Vol. 28, pp. 11827-11833 (2012).
Wang, S., Wang, G. and Jiang, F., Luo, M. and Li, H. “Chemical Looping Combustion of Coke Oven Gas by using MgAl2O4 as Oxygen Carrier,” Energ. Environ. Sci., Vol.3, pp. 1353-1360 (2010).
Yang, J.B., Cai, N.S. and Li, Z.H. “Hydrogen Production from the Steam-Iron Process with Direct Reduction of Iron Oxide by Chemical Looping Combustion of Coal Char,” Energ Fuels, Vol.22, pp. 2570-2579 (2008).
Zafer, Q., Mattisson, T. and Gevert, B. “Integrated Hydrogen and Power Production with CO2 Capture Using Chemical-Looping Reforming-Redox Reactivity of Particles of CuO, Mn2O3, NiO and Fe2O3 Using SiO2 as a Support,” Ind. Eng. Chem. Res., Vol.44, pp. 3485-3496 (2005).
Zafer, Q., Mattisson, T. and Gevert, B. “Redox Investigation of Some Oxides of Transition-State Ni, Cu, Fe, and Mn Supported on SiO2 and MgAl2O4,” Energy Fuels, Vol.20, pp. 34-44 (2006).