研究生: |
蔣文暉 Wen-hui Chaing |
---|---|
論文名稱: |
連接器挾持力感測器設計與分析 Design and Analysis of Normal Force Sensor of Connectors |
指導教授: |
李維楨
Wei-chen Lee |
口試委員: |
趙振綱
Ching-kong Chao 周振嘉 Chen-chia Chou |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 機械工程系 Department of Mechanical Engineering |
論文出版年: | 2006 |
畢業學年度: | 94 |
語文別: | 中文 |
論文頁數: | 110 |
中文關鍵詞: | 連接器 、正向力 、微機電系統 、力量感測器 |
外文關鍵詞: | connector, normal force, MEMS, force sensor |
相關次數: | 點閱:218 下載:0 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
夾持力的檢測在連接器中相當的重要,連接器的夾持力需要保持在100 gf以上,訊號的傳輸才能保持穩定。傳統上連接器夾持力的檢測,需要將連接器的外殼及內部結構移除,探針才能伸入連接器內部進行連接器夾持力的量測。此破壞性檢測的方式所量測到的結果可能因為連接器結構已經被破壞,導致量測結果有所誤差。本研究利用ANSYS有限元素分析軟體,設計較佳的感測器彈性體結構,再利用微機電技術,製作微小型力量感測器。微小型力量感測器將與PCB板結合在一起,能夠不破壞連接器本身結構,直接的量測連接器的夾持力,如此所量測的結果能夠更加的準確。本研究中發現於考慮較大的量測訊號輸出時,長方形薄膜結構優於正方形薄膜結構。
Measuring the normal force of a connector is very important. The normal force of a connector needs to be above 100 gf, so the transmission of the signal can remain stable. In general, measuring the normal force of a connector needs to remove part of the plastic housing and structure of a connector, so that the probe can be inserted into the connector to measure the normal force. Because the structure of the connector has been changed, the measurement results may be inaccurate. In the study, we use ANSYS software to design better spring element of a minature force sensor, and then fabricate it by MEMS technology. The miniature force sensor will be packaged with a PCB so that it can be employed to measure the normal force of the connector directly without destructing the structure of the connector. It is found that the effect of rectangular thin film is better than square thin film in terms of maximizing the measuring signal.
[1] 徐文祥,"微機電系統技術與應用",第1~5頁,新竹市,行政院國家科學委員會精密儀器發展中心,民國92年。
[2] 教育部高工進修網站微奈米技術, http://elearning.stut.edu.tw/m_facture/Nanotech/Web/ch1.htm
[3] Baltes, H., "COMS as sensor technology", Sensors and Actuators A, Vol.37-38,pp.51-56(1993).
[4] 徐泰然,"微機電系統與微系統",第1~325頁,台北,普林斯頓國際有限公司,民國92年。
[5] Mroczkowski, R.S., Electronic Connector Handbook, New York, NY,McGraw Hill,pp.212(1998).
[6] Mroczkowski, R.S., Electronic Connector Handbook, McGraw Hill, New York,pp.118(1998).
[7] Mroczkowski, R.S., Electronic Connector Handbook, New York, NY,
McGraw Hill,p.204(1998).
[8] 刑泰剛,"微機電系統技術與應用",第467~474頁,新竹市,行政院
國家科學委員會精密儀器發展中心,民國92年。
[9] Gieles, A. C. M., "Subminiature Silicon Pressure Transducer, " IEEE
International Solid-State Circuits Conference, Digest of Technical
Papers, Vol.12, pp.108-109(1969).
[10] Robert, G. and Li, Z., "Micromachined microsensors for manufacturing, " IEEE Instrumentation & Measurement Magazine, Vol.7, Issue2, pp.320-26(2004).
[11] Hsu, T. R., MEMS & MICROSYSTEMSM Design and Manufacture,
McGraw-Hill,pp.103-273(2002).
[12] 莊達人,"VLSI製造技術",第291~296頁,台北,高立圖書,民國91年。
[13] Marc, M., Fundamentals of Microfabrication, Boca Raton, New York,
pp.89-96(1997).
[14] Walter, L., "Silicon microstructuring technology", Materials science and
engineering, R17, pp.1-55(1996).
[15] Lee, D. B., "Anisotropic etching of silicon ", Journal of Applied physics,
Vol.40, No.11, pp.4569-4574(1969).
[16] Yamamoto, M., Iriye, Y., Asaumi, K., Shikida, M., Tamashiro, T., and
Sato, K., "Characterization of orientation-dependent etching properties of
single-crystal silicon effect of KOH concentration", Sensors an Actuators
A Physical, Vol.64, No.1, pp87-93(1998).
[17] Marc, M., Fundamentals of Microfabrication, Boca Raton, New York,
pp.163-190(1997).
[18] Price, J.B., "Semiconductor Silicon", The Electrochemical Society
Softbound Proceeding Series, pp.339-353(1973).
[19] Zubel, I., and Kramkowska, M., "The effect of isopropyl alcohol on
etching rate and roughness of (100) Si surface etched in KOH and
TMAH solution", Sensors and Actuators A Physical, Vol.93,
pp138-147(2001).
[20] Richard, C.J., INTRODUCTION TO MICROELECTRONIC
FABRICATION, Prentic Hall,New Jersey,pp.109-119(1998).
[21] Erwin, P. and Lutz, D., "Force calibration of stylus instruments
using silicon microcantilevers", Sensors and Actuators, Vol.123-124,
pp.137-145(2005).
[22] Tao, M., Wen J.L., Yu G., Yong C., Lin N., and Ming H.C., "An
integrated MEMS three-dimensional tactile sensor with large force
range", Sensors and Actuators, Vol.80, pp.155-162(2000).
[23] 刑泰剛,"微機電系統技術與應用",第467~474頁,新竹市,行政院
國家科學委員會精密儀器發展中心,民國92年。
[24] Madou, M. J., Fundamentals of Microfabrication, Boca raton, New York,
pp.148-161(1997).
[25] Robert F., Pierret, Gerold W., and Neudeck, Semiconductor undamentals
Second Edition VOLUME I, ADDISON-WESLEY, New York,
pp.71(1989).
[26] 周元昉,"壓阻式壓力感測器講義",台灣大學機械系。
[27] Tao, M., Wen, J.L., Yu, G., Yong, C., Lin, N., and Ming H.C.,
"An integrated MEMS three-dimensional tactile sensor with large force
range, " Sensors and Actuators, Vol.80, pp.252(2000).
[28] Robert, F., Pierret, Gerold W., and Neudeck, Semiconductor undamentals
Second Edition Vol. I, pp.66-70(1988).
[29] 蓋永鋒,"微型壓阻式壓力感測器製作之研究",國立成功大學工
程科學系碩士論文,民國89年。
[30] Mimiwaty, M.N., Badariah, B., and Burhanuddin, Y.M., "The Effects of Temperature and KOH Concentration on Silicon Etching Rate and Membrane Surface Roughness," Semiconductor Electronics, 2000. Proceeding. ICSE 2000.IEEE International Conference on 19-21 Dec pp.524-528(2000).
[31] 何建龍,"壓電微型加速度計之製作與動態特性量測",國立台灣科技大學機械工程系碩士學位論文,民國93。