研究生: |
林禹丞 Yu-Cheng Lin |
---|---|
論文名稱: |
矽烷偶合劑接枝之氧化石墨烯及熱脫層氧化石墨烯之合成及探討其對乙烯基酯樹脂之聚合固化樣品微觀型態結構、體積收縮、機械性質、熱傳導及導電性質的影響 Synthesis of silane-grafted graphene oxide (sg-GO) and silane-grafted thermally reduced graphene oxide (sg-TRGO), and their effects on cured sample morphologies, volume shrinkage, mechanical properties, and thermal and electrical conductivities for vinyl ester resins |
指導教授: |
黃延吉
Yan-Jyi Huang |
口試委員: |
陳崇賢
Chorng-Shyan Chern 邱文英 Wen-Yen Chiu |
學位類別: |
碩士 Master |
系所名稱: |
工程學院 - 化學工程系 Department of Chemical Engineering |
論文出版年: | 2019 |
畢業學年度: | 107 |
語文別: | 中文 |
論文頁數: | 199 |
中文關鍵詞: | 氧化石墨烯 、熱脫層氧化石墨烯 、矽烷接枝之氧化石墨烯 、矽烷接枝之熱脫層氧化石墨烯 、抗收縮劑 、乙烯基酯樹脂 、聚合固化 、體積收縮 、機械性質 、熱傳導性質 、導電性質 、接枝效率 |
外文關鍵詞: | graphene oxide, silane-grafted graphene oxide, thermally reduced graphene oxide, silane-grafted thermally reduced graphene oxide, low-profile additive, vinyl ester resins, curing, volume shrinkage, mechanical properties, grafting efficiency |
相關次數: | 點閱:315 下載:1 |
分享至: |
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
本文探討添加氧化石墨烯(GO)、矽烷接枝氧化石墨烯(sg-GO)、熱脫層氧化石墨烯(TRGO)以及矽烷接枝熱脫層氧化石墨烯(sg-TRGO)等數種特用添加劑的合成及其對苯乙烯(St)/乙烯基酯樹脂(VER) /特用添加劑三成份系統於120℃/150℃階段性恆溫固化之微觀型態結構、體積收縮、機械性質、熱傳導及導電性之影響。
GO是將平均粒徑為75μm的天然石墨粉以改良Hummers 法製得;熱脫層氧化石墨烯(TRGO) 則是將氧化石墨烯(GO)置於1050℃的高溫爐中30秒熱脫層而得。
矽烷接枝氧化石墨烯(sg-GO)為帶有乙烯基團的矽烷偶合劑,即甲基丙烯醯氧丙基三甲氧基矽烷(MPS),做為表面改質劑,在GO(or TRGO)/MPS/甲苯三者的重量比為1:5:94下,每次對氧化石墨烯(GO)於100℃下進行表面處理3hr,以不同反應次數(一或三次反應)得到不同接枝率之sg-GO或sg-TRGO。另外,亦利用FTIR計算一次與三次反應下之接枝密度,最後吾人將合成之添加劑(GO, sg-GO, TRGO, sg-TRGO)添加到VER中,亦研究其對St/VER(n=2)/添加劑三成分系統聚合固化後之體積收縮、機械性質、熱傳導及導電性之影響。
The effects of graphene oxide (GO), silane-grafted graphene oxide (sg-GO), thermally reduced graphene oxide (TRGO), and silane-grafted thermally reduced graphene oxide (sg-TRGO) as special addictives on the cured sample morphologies, volume shrinkage characteristics and mechanical properties for low-shrink vinyl ester resins (VER) cured at 120℃ were investigated.
The TRGO was produced by placing the GO in a high-temperature furnace kept at 1050 ℃ for 30 s, which was synthesized from natural graphite powder with average particle size of 75 μm by a modified Hummers method. The sg-GO was synthesized by using the silane coupling agent bearing C=C bonds, namely, γ-methacryloxy propyl trimethoxy silane (MPS), as a surface modifier for the surface treatment of GO at 100℃ for 3 hr with different times of reaction for surface treatment between GO and MPS (n=1 or 3), and with a fixed weight ratio of GO/MPS/solvent at 1:5:94. The grafting density of MPS on the GO or TRGO has been measured by FTIR. Finally, the effects of additives synthesized, such as, GO, sg-GO, TRGO, and sg-TRGO, on the volume shrinkage, mechanical properties, thermal and electrical conductivities for the styrene(St)/vinyl ester resin(VER)/additive ternary systems after the cure have also been investigated.
[1] A. Almagableh, P. R.Mantena, A. Alostaz, W. Liu, L. T. Drzal, eXPRESS Polym. Lett. 2009, 11, 724-732.
[2] Z. Guo, K. Lei, Y. Li, W. Liu, H. W. Ng, P. Sergy, H. Thomas, Compos. Sci. Technol. 2008, 68, 1513-1520.
[3] S. Dua, R. L. McCullough, G. R. Palmese, Polym. Compos. 1999, 20 379-391.
[4] W. Posthumus, P.C.M.M. Magusin, J.C.M. Brokken-Zijp, A.H.A. Tinnemans, R. van der Linde, J. Colloid and Interface Sci. 2004, 269, 109-116.
[5] 鍾宛倫, 碩士論文, 台灣科技大學, 2014.
[6] R.B. Burn, “Polyester Molding Compounds”, Marcel Dekker, Inc, New York, 1982.
[7] 賴耿陽, 環氧樹脂應用實務, 復漢出版社, 台灣, 1999.
[8] 陳東課, 環氧樹脂在基層板之應用, 化工技術第四卷第五期, 1996.
[9] T.D.C. Company, PCT Int.Appl.WO986/07067, 1986.
[10] R. E. Young, in “Unsaturated Polyester Technology”, Ed. P.F. Bruins, Gordon and Breach Science Publishers, 1976.
[11] F. Fekete, in “Unsaturated Polyester Technology”, Ed. P.F. Bruins, Gordon and Breach Science Publishers, 1976, P.28.
[12] S. V. Levchik, G. Camino, M. P. Luda, L. Costa, G. Muller, B. Costes, Polymer Degradation and Stability , 60, 169(1998).
[13] E. J. Bartkus, C. H Kroekel, Appl. Polym. Symp. 1970, 15, 113.
[14] V.A. Pattison, R.R. Hindersinn, W.T. Schwartz, Journal of Applied Polymer Science 18 (1974) 2763-2771.
[15] V.A. Pattison, R.R. Hindersinn, W.T. Schwartz, Journal of Applied Polymer Science 19 (1975) 3045-3050.
[16] H.G. Kia, Sheet Molding Compounds: Science and Technology, Hanser1993.
[17] Y.J. Huang, C.C. Su, Journal of Applied Polymer Science 55 (1995) 305-322.
[18] Y.-J. Huang, L.-D. Chen, Polymer 39 (1998) 7049-7059.
[19] Y.-J. Huang, J.C. Horng, Polymer 39 (1998) 3683-3695.
[20] L. Suspène, D. Fourquier, Y.-S. Yang, Polymer 32 (1991) 1593-1604.
[21] W. Li, L. Lee, K. Hsu, Polymer 41 (2000) 711-717.
[22] C.B. Bucknall, I.K. Partridge, M.J. Phillips, Polymer 32 (1991) 636-640.
[23] Y.J. Huang, T.S. Chen, J.G. Huang, F.H. Lee, Journal of Applied Polymer Science 89 (2003) 3336-3346.
[24] Y.-J. Huang, C.-M. Liang, Polymer 37 (1996) 401-412.
[25] J.P. Dong, J.H. Lee, D.H. Lai, Y.J. Huang, Journal of Applied Polymer Science 98 (2005) 264-275.
[26] H. Kim, A.A. Abdala, C.W. Macosko, Macromolecules 43 (2010) 6515-6530.
[27] Y.J. Wan, L.X. Gong, L.C. Tang, L.B. Wu, J.X. Jiang, Compos. Pt. A-Appl. Sci. Manuf. 64 (2014) 79-89.
[28] Y.J. Wan, L.C. Tang, L.X. Gong, D. Yan, Y.B. Li, L.B. Wu, J.X. Jiang, G.Q. Lai, Carbon 69 (2014) 467-480.
[29] C. Botas, P. Álvarez, C. Blanco, R. Santamaría, M. Granda, M.D. Gutiérrez, F. Rodríguez-Reinoso, R. Menéndez, Carbon 52 (2013) 476-485.
[30] H. Kim, Y. Miura, C.W. Macosko, Chemistry of Materials 22 (2010) 3441-3450.
[31] J. Zang, Y.J. Wan, L. Zhao, L.C. Tang, Macromolecular Materials and Engineering 300 (2015) 737-749.
[32] A. K. Appel, R. Thomann, R. Mülhaupt, Polymer 53 (2012) 4931-4939.
[33] X. Wang, W. Xing, L. Song, B. Yu, Y. Hu, G.H. Yeoh, Reactive and Functional Polymers 73 (2013) 854-858.
[34] A. Chaturvedi, A. Tiwari, A. Tiwari, Adv Mater Lett 4 (2013) 656-661.
[35] O. Eksik, S.F. Bartolucci, T. Gupta, H. Fard, T. Borca-Tasciuc, N. Koratkar, Carbon 101 (2016) 239-244.
[36] E. P. Plueddemann, Silane Coupling Agents, Springer US2013.
[37] E. P. Plueddemann, H.A. Clark, Mod. Plast 40(6) (1963) 133.
[38] C. S. Brazel, S,L, Rosen, Fundamental Principle of Polymeric Materials Third Edition, New Jersey: John Wiley & Sons, Inc., 2012
[39] Y. Yang, L.J. Lee, Polymer 29 (1988) 1793-1800.
[40] 盧天智, 碩士論文. 台灣科技大學 (1989).
[41] K. Horie, I. Mita, H. Kambe, Journal of Polymer Science Part A: Polymer Chemistry 7 (1969) 2561-2573.
[42] Y. J. Huang, C. C. Su, J. Appl. Polym. Sci. 1995, 55, 305.
[43] Y. J. Huang, C.C. Su, Polym. 1994, 35, 2397.
[44] V. A. Pattison, R. R. Hindersinn, W. T. Schwartz, J. Appl. Polym. Sci. 1974, 18, 2763.
[45] V. A. Pattison, R. R. Hindersinn, W. T. Schwartz, J. Appl. Polym. Sci. 1975, 19 3045.
[46] Y. J. Huang, T. S. Chen, J. G. Huang, F. H. Lee, J. Appl. Polym. Sci. 2003, 89, 3336
[47] K. E. Atkins, in “Sheet Molding Compound :Science and Technology” Ed., H.G. Kia, Hanser Publishers, 1993, Ch4.
[48] C. B. Bucknall, I. K. Partridge, M. J. Phillips, Polym. 1991, 32, 786.
[49] T. Mitani, H. Shiraishi, K. Honda, G.E. Owen, 44th Annual Conference Composite Institute, SPI, Session 12-F, 1989.
[50] W. D. Cook, O. Delatycki, J. Polym. Sci. Polym. Phys. Ed. 1974, 12, 2111.
[51] Y. J. Huang, S. C. Lee, J. P. Dong, J. Appl. Polym. Sci. 2000, 78, 558.
[52] Y. J. Huang, T. S. Chen, J. G. Huang, F. H. Lee, J. Appl. Polym. Sci. 2003, 89, 3347.
[53] 陳彥博, 碩士論文. 台灣科技大學 (2019).
[54] 林暐靜, 碩士論文. 台灣科技大學 (2019).
[55] W.S. Hummers Jr, R.E. Offeman, Journal of the American Chemical Society 80 (1958) 1339-1339.
[56] C. H. Schniepp, J. L. Li, M. J. McAllister, H. Sai, H. A. Margarita, D. H. Adamson, R. K. Prud’homme, R. Car, D. A. Saville, I. A. Aksay, J. Phys. Chem. B. 2006, 17, 8535.
[57] Y. Yang, J. Wang, J. Zhang, J. Liu, X. Yang, H,. Zhao, Langmuir, 2009, 25, 118.
[58] F. Beckert, C. Friedrich, R. Thomann, R. Mulhaupt, Macromol. 2012, 45, 7083.
[59] 邱冠智, 碩士論文. 台灣科技大學 (2018).
[60] 王妤榛, 碩士論文. 台灣科技大學 (2016).
[61] 廖翊成, 碩士論文. 台灣科技大學 (2017).
[62] 江義駿, 碩士論文. 台灣科技大學 (2018).
[63] S. Colonna, O. Monticelli, J. Gomez, C. Novara, G. Saracco, A. Fina, Polymer 102 (2016) 292-300.
[64] C. Hontoria-Lucas, A. Lopez-Peinado, D. Lopez-Gonzalez, M. L. Rojas-Cervantes, R. M. Martin-Ara nda, Carbon. 1995, 33, 1585-1592.
[65] G. Xue, J.L. Koenig, H. Ishida, D.D. Wheeler, Rubber chemistry and technology 64 (1991) 162-171.
[66] N. Suzuki, H. Ishida, 1996
[67] P. Innocenzi, G. Brusatin, M. Guglielmi, R. Bertani, Chemistry of Materials 11 (1999) 1672-1679.
[68] D. Lin-Vien, N.B. Colthup, W.G. Fateley, J.G. Grasselli, The Handbook of Infrared and Raman Characteristic Frequencies of Organic Molecules, Elsevier Science1991.
[69] J. Coates, Encyclopedia of analytical chemistry (2000).
[70] L.G.P. Moraes, R.S.F. Rocha, L.M. Menegazzo, E.B.d. Araújo, K. Yukimito, J.C.S. Moraes, Journal of Applied Oral Science 16 (2008) 145-149.
[71] R. Sa, Y. Yan, Z. Wei, L. Zhang, W. Wang, M. Tian, ACS Appl. Mater. Interfaces 6 (2014) 21730-21738.
[72] S. Ganguli, A.K. Roy, D.P. Anderson, Carbon 46 (2008) 806-817.
[73] R. Aradhana, S. Mohanty, S.K. Nayak, Polymer 141 (2018) 109-123.